Projects / Fridge door left open alarm

Fridge door left open alarm

Beginner1 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. DIGISPAR

    Build it on a breadboard

    Test the reading in light and dark.

  2. DIGISPAR

    Set the threshold

    BRIGHT between the two.

  3. DIGISPAR

    Remove the power LED

    Cuts the drain.

  4. DIGISPAR++

    Wire the coin cell

    Bypass the regulator.

  5. DIGISPAR

    Fix it near the lamp

    Not touching food.

  6. DIGISPAR

    Test for 60 seconds

    Door open.

  7. DIGISPAR++

    Watch it for a week

    Check the cell in the cold.

In short

How do you build a fridge door left open alarm?

A light sensor inside the fridge notices the lamp is on for over a minute and beeps until the door is closed. You need Digispark ATtiny85 USB board, LDR Photoresistor, Resistor 10 kΩ, Active buzzer 5 V, CR2032 coin cell and CR2032 coin cell holder. It takes 7 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Coin cell holder plusDigispark 5V pin and LDR one legPowers the board directly (the regulator is bypassed)
Coin cell holder minusDigispark GNDGround
LDR other legDigispark P2 and one end of the 10 k resistorDivider output
10 k resistor other endDigispark GNDDivider bottom
Buzzer plusDigispark P0Beep
Buzzer minusDigispark GNDReturn

Code

Instead of a reed switch, this uses the fridge's own lamp: an LDR and a fixed resistor make a divider whose reading rises when the lamp is on, which only happens when the door is open. The Digispark sleeps almost all the time, waking every four seconds on the watchdog timer, and only beeps when it has seen light fifteen times in a row, about a minute, so a quick look into the fridge does nothing. Settings that make a coin cell last: run at 1 MHz and use the No USB board setting; bypass the on-board regulator and feed the 3 V cell to the 5V pin; and remove the on-board power LED, which would drain the cell in days. A coin cell cannot supply much, so use a small buzzer and keep beeps short. Cold reduces battery capacity, so test it for a week in your fridge. Mount the board away from food and moisture, and do not rely on it alone to protect food or medicine. Adjust BRIGHT after trying the lamp on and off. Arduino IDE with the Digistump AVR boards package, board "Digispark (1 MHz - No USB)" so it runs on a 3 V coin cell. The USB bootloader waits a few seconds at power-up.

Runs on a virtual Digispark ATtiny85 in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Fridge door alarm: sleeps in 4 second steps, beeps if the lamp has been on for about 60 seconds.
// Board: Digispark ATtiny85 at 1 MHz. LDR on P2 (analog channel 1), buzzer on P0.
#include <avr/sleep.h>
#include <avr/wdt.h>
#include <avr/interrupt.h>
const uint8_t BUZ = 0;
const uint8_t LDR_CH = 1;                   // P2 is analog channel 1
const int BRIGHT = 500;                     // adjust after testing in your fridge
const uint8_t LIMIT = 15;                   // 15 wakes of 4 s is about 60 s
uint8_t brightCount = 0;
ISR(WDT_vect) {}
void sleep4s() {
  cli();
  MCUSR &= ~(1 << WDRF);
  WDTCR |= (1 << WDCE) | (1 << WDE);
  WDTCR = (1 << WDIE) | (1 << WDP3);        // 4 second watchdog interrupt
  ADCSRA &= ~(1 << ADEN);                   // ADC off while sleeping
  set_sleep_mode(SLEEP_MODE_PWR_DOWN);
  sleep_enable();
  sei();
  sleep_cpu();
  sleep_disable();
  ADCSRA |= (1 << ADEN);
}
void setup() {
  pinMode(BUZ, OUTPUT);
}
void loop() {
  sleep4s();
  int v = analogRead(LDR_CH);
  if (v > BRIGHT) brightCount++; else brightCount = 0;
  if (brightCount >= LIMIT) {
    for (int i = 0; i < 3; i++) { digitalWrite(BUZ, HIGH); delay(150); digitalWrite(BUZ, LOW); delay(150); }
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Door open under 30 sSilent
Door open over a minuteThree beeps every 4 seconds
Door closedStops at once
Sleep currentVery low

If it does not work

Never beeps

Lower BRIGHT or move the LDR nearer the lamp.

Beeps in the dark

Raise BRIGHT or shield the LDR from the display light.

Resets

A weak coin cell; use a fresh one.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the fridge door left open alarm?

Digispark ATtiny85 USB board, LDR Photoresistor, Resistor 10 kΩ, Active buzzer 5 V, CR2032 coin cell and CR2032 coin cell holder.

How long does the fridge door left open alarm take to build?

About 60 minutes for a beginner maker, in 7 steps.

How do I know the fridge door left open alarm works?

Door open under 30 s: Silent. Door open over a minute: Three beeps every 4 seconds. Door closed: Stops at once.

Never beeps: what should I check?

Lower BRIGHT or move the LDR nearer the lamp.

Beeps in the dark: what should I check?

Raise BRIGHT or shield the LDR from the display light.

Resets: what should I check?

A weak coin cell; use a fresh one.