Projects / Gain of three small NPN transistors

Gain of three small NPN transistors

Beginner1.3 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. Check each pinout

    Flat face toward you, note the pin order.

  2. Build the base resistor

    Three 100 kilohm in series to the base.

  3. Build the collector load

    330 ohm from the red rail to the collector.

  4. 2N3904BC337BC548

    Connect the first transistor

    Emitter to the blue rail.

  5. Measure Vbe and the drop

    Across the 330 ohm and base to emitter.

  6. Calculate the gain

    Collector current divided by base current.

  7. Swap in the next type

    Repeat for all three.

  8. Test two of one type

    Compare the spread.

In short

How do you build a gain of three small NPN transistors?

Measure the current gain of three common small NPN types on the same circuit and see how much they vary. You need 2N3904 NPN transistor, BC337 NPN transistor (800 mA), BC548 NPN transistor, Resistor 100 kΩ × 3, Resistor 330 Ω, 9 V battery, 9 V battery snap with DC jack, Digital multimeter, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points. It takes 8 steps and about 75 minutes.

Level
Beginner
Time
About 75 min
Parts
10
See the electronics first. This build uses transistor switch. Try a transistor switch in the circuit builder and watch the voltages and currents before you wire it.

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
9 V battery positiveRed railSupply
9 V battery negativeBlue railGround
Three 100 kilohm resistors in seriesRed rail to the transistor baseAbout 300 kilohm sets a small base current
330 ohm resistorRed rail to the transistor collectorCollector load
Transistor emitterBlue railGround
Multimeter (volts)Across the 330 ohm resistorCollector current from the voltage drop
Multimeter (volts)Base to emitterReads Vbe, about 0.65 V

Code

The current gain of a transistor, often written hFE or beta, is the ratio of collector current to base current, and datasheets give it as a wide range rather than a number: a 2N3904 can be anywhere between about 100 and 300. This build lets you measure it for yourself with a resistor and a multimeter. A string of three 100 kilohm resistors from a 9 volt battery sets a base current of about 28 microamps, small and nearly the same for any transistor because it is set by the resistor, not the transistor. The collector current then follows from the gain, and you find it by measuring the voltage across the 330 ohm collector resistor and dividing by 330. The gain is the collector current divided by the base current. Expect values from roughly 100 up to a few hundred, with real differences between types and even between two parts of the same type, which shows why circuits that depend on exact gain are fragile and why switch circuits are designed to work for any gain. The pinout is the trap: the 2N3904 is emitter, base, collector from the left, but the BC548 and BC337 are collector, base, emitter, so a transistor put in the wrong way will simply show a very low gain. Warm the transistor with a fingertip and watch the collector current rise, because gain increases with temperature.

Build notes (no code needed for this build)

Pinouts, flat face toward you, legs down, left to right:
  2N3904 : Emitter, Base, Collector
  BC548  : Collector, Base, Emitter
  BC337  : Collector, Base, Emitter
These are NOT the same order, so check each part before wiring it.

Method:
  Base current   Ib = (9 V - Vbe) / 300 kilohm. With Vbe = 0.65 V this is about 28 microamps.
  Collector current  Ic = (voltage across the 330 ohm resistor) / 330.
  Gain  hFE = Ic / Ib.
The transistor stays in its active region as long as the collector voltage stays above about 1 V. With 330 ohm the drop would only reach that limit if the gain were near 950.

Example: if the voltage across the 330 ohm is 1.50 V, Ic = 4.5 mA and the gain is 4.5 mA / 28 microamps = about 160.
Typical results: 2N3904 about 100 to 300, BC548 about 200 to 450 depending on the group letter, BC337 about 100 to 600 depending on the suffix.
Warm a transistor with your fingertip and the gain rises, which is why gain is unreliable for precise circuits.

Table: type, Vbe, voltage across 330 ohm, Ic, Ib, gain. Test two parts of the same type to see the spread.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
VbeAbout 0.6 to 0.7 V
Voltage across the 330 ohmAbout 1 to 3 V
Base currentAbout 28 microamps
GainRoughly 100 to 400 depending on the type
Warm the transistorGain rises a little

If it does not work

Collector voltage near 9 V

Transistor is off or in backwards, check the pinout.

Collector voltage near 0 V

The gain is very high or the base resistor is too small.

Gain very low

Pin order wrong, swap the legs.

Readings drift

Hold the transistor steady and let it settle.

Voltage across 330 ohm is zero

Check the base resistor chain.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the gain of three small NPN transistors?

2N3904 NPN transistor, BC337 NPN transistor (800 mA), BC548 NPN transistor, Resistor 100 kΩ × 3, Resistor 330 Ω, 9 V battery, 9 V battery snap with DC jack, Digital multimeter, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points.

How long does the gain of three small NPN transistors take to build?

About 75 minutes for a beginner maker, in 8 steps.

How do I know the gain of three small NPN transistors works?

Vbe: About 0.6 to 0.7 V. Voltage across the 330 ohm: About 1 to 3 V. Base current: About 28 microamps.

Collector voltage near 9 V: what should I check?

Transistor is off or in backwards, check the pinout.

Collector voltage near 0 V: what should I check?

The gain is very high or the base resistor is too small.

Gain very low: what should I check?

Pin order wrong, swap the legs.

Readings drift: what should I check?

Hold the transistor steady and let it settle.