Projects / ESP32 laundry cycle end beeper

ESP32 laundry cycle end beeper

Beginner2.2 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. ESP32

    Wire the sensor

    VCC to 3V3, GND to GND, DO to GPIO27.

  2. ESP32

    Wire the buzzer

    GPIO26 and GND.

  3. ESP32

    Upload the sketch

    Open the Serial Monitor at 115200.

  4. ESP32

    Tap the sensor

    The board's light flickers and the count rises.

  5. ESP32

    Set the dial

    So that the light stays off at rest.

  6. ESP32

    Fix the sensor

    To the side panel of the machine with tape.

  7. ESP32

    Run a short wash

    The count rises, and after it ends five quiet minutes later it beeps.

In short

How do you build an ESP32 laundry cycle end beeper?

An ESP32 with a vibration sensor stuck on a washing machine notices when the shaking stops for five minutes and sounds a short beep, so you know the load is done. You need ESP32 DevKit V1, Vibration sensor module (SW-420), Active buzzer 5 V and Breadboard 830 Tie Points. It takes 7 steps and about 130 minutes.

Level
Beginner
Time
About 130 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Vibration module VCCESP32 3V3Power at 3.3 V
Vibration module GNDESP32 GNDCommon ground
Vibration module DOESP32 GPIO27Pulses when it shakes
Buzzer +ESP32 GPIO26Alert sound
Buzzer -ESP32 GNDGround

Code

The SW-420 is a vibration switch on a small board with a comparator. When the board shakes, the switch inside opens and closes, and the output pin pulses. A small dial on the board sets how much shaking it takes. The program counts the pulses in an interrupt, which runs the moment a pulse arrives so that none are missed, and every minute it looks at the count. Five or more pulses in a minute means the machine is running. After it has been running, five minutes in a row with fewer than five pulses means the wash has finished, so the buzzer sounds. The delay of five minutes covers the quiet soaking pauses in a wash cycle. Stick the sensor to the side panel of the machine, not near a hot surface, keep the wiring clear of water and moving parts, and set the dial so that the board's light flickers only while the machine is shaking.

Runs on a virtual ESP32 Dev Module in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const int SENSOR = 27;
const int BUZZER = 26;

const unsigned long MINUTE = 60000UL;
const int RUN_PULSES = 5;                           // shakes per minute that mean the machine is running
const int QUIET_MINUTES = 5;                        // quiet minutes that mean it has finished

volatile unsigned long pulses = 0;
bool running = false;
int quietCount = 0;
unsigned long windowStart = 0;

void IRAM_ATTR onShake() {
  pulses++;
}

void beepFinished() {
  for (int i = 0; i < 5; i++) {
    digitalWrite(BUZZER, HIGH); delay(150);
    digitalWrite(BUZZER, LOW);  delay(150);
    digitalWrite(BUZZER, HIGH); delay(150);
    digitalWrite(BUZZER, LOW);  delay(1500);
  }
}

void setup() {
  Serial.begin(115200);
  pinMode(BUZZER, OUTPUT);
  pinMode(SENSOR, INPUT);
  attachInterrupt(digitalPinToInterrupt(SENSOR), onShake, FALLING);
  windowStart = millis();
}

void loop() {
  if (millis() - windowStart >= MINUTE) {
    noInterrupts();
    unsigned long count = pulses;
    pulses = 0;
    interrupts();
    windowStart = millis();
    Serial.print("Shakes this minute: "); Serial.println(count);

    if (count >= RUN_PULSES) {
      running = true;
      quietCount = 0;
    } else if (running) {
      quietCount++;
      if (quietCount >= QUIET_MINUTES) {
        Serial.println("Finished");
        beepFinished();
        running = false;
        quietCount = 0;
      }
    }
  }
  delay(50);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
At restShakes this minute: 0
Machine spinningMany shakes each minute
Machine stopsCount falls to 0
Five quiet minutes laterFive beep groups and Finished
Next loadStarts watching again

If it does not work

Count is always zero

Turn the dial towards more sensitive and check DO is on GPIO27.

Count is high at rest

Turn the dial the other way, and fix the sensor firmly so it does not rattle.

Alerts during the soak pause

Raise QUIET_MINUTES to 8.

Never alerts

Check the buzzer wires and that the machine reached five shakes a minute.

Sensor falls off

Use stronger tape or a magnet.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the ESP32 laundry cycle end beeper?

ESP32 DevKit V1, Vibration sensor module (SW-420), Active buzzer 5 V and Breadboard 830 Tie Points.

How long does the ESP32 laundry cycle end beeper take to build?

About 130 minutes for a beginner maker, in 7 steps.

How do I know the ESP32 laundry cycle end beeper works?

At rest: Shakes this minute: 0. Machine spinning: Many shakes each minute. Machine stops: Count falls to 0.

Count is always zero: what should I check?

Turn the dial towards more sensitive and check DO is on GPIO27.

Count is high at rest: what should I check?

Turn the dial the other way, and fix the sensor firmly so it does not rattle.

Alerts during the soak pause: what should I check?

Raise QUIET_MINUTES to 8.

Never alerts: what should I check?

Check the buzzer wires and that the machine reached five shakes a minute.