Build it step by step
0 of 7 doneBuild the ladder
Three resistor groups from rail to ground.
Measure the taps
About 8.1 V and 4.1 V.
Add the comparators
LM393 as a window.
Add the LEDs
Green good, red fail.
Add the sense node
1 MΩ and a pad.
Test with resistors
1 MΩ passes, 100 kΩ and open fail.
Test your strap
Daily check.
How do you build an ESD wrist strap tester?
Test that your ESD strap has the right resistance to ground before you start work. You need Anti-static wrist strap, LM393 Comparator, Resistor 1 kΩ × 2, Resistor 1 MΩ × 2, LED 5 mm green, LED 5 mm red, Resistor 330 Ω × 2, Tactile push button 6 mm, 9 V battery, 9 V battery snap with DC jack, Resistor 10 kΩ × 6, Resistor 4.7 kΩ and Resistor 2 kΩ. It takes 7 steps and about 60 minutes.
- Level
- Intermediate
- Time
- About 60 min
- Parts
- 13
Parts list
- Tools & InstrumentsBuy
- Integrated CircuitsBuyLM393 Comparator × 1
- PassivesBuyResistor 1 kΩ × 2
- PassivesBuyResistor 1 MΩ × 2
- SemiconductorsBuyLED 5 mm green × 1
- SemiconductorsBuyLED 5 mm red × 1
- PassivesBuyResistor 330 Ω × 2
- SwitchesBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
- PassivesBuyResistor 10 kΩ × 6
- PassivesBuyResistor 4.7 kΩ × 1
- PassivesBuyResistor 2 kΩ × 1
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery plus | Test button, then the supply rail | Power only while testing |
| 1 MΩ resistor | Rail to the sense node and finger pad | Series resistor |
| Strap cord | Sense node through your body to circuit ground | Strap under test |
| Reference ladder | 6.7 kΩ (4.7k plus 2k), then 30 kΩ, then 30 kΩ (three 10 kΩ each) from rail to ground | Two limits |
| Upper tap (8.1 V) | LM393 pin 5 | High limit |
| Lower tap (4.1 V) | LM393 pin 2 | Low limit |
| Sense node | LM393 pins 3 and 6 | Reading |
| LM393 pins 1 and 7 | 1 kΩ to rail, green LED through 330 Ω to ground | Good indicator |
| Red LED | Cathode to pins 1 and 7, anode through 1 kΩ to the rail | Fail indicator |
No code needed
A wrist strap should have about 1 MΩ in the cord, so static drains slowly and safely, and not 0 Ω, which would be a shock risk, or an open circuit, which gives no protection. This tester uses a 9 V battery and a 1 MΩ series resistor, so the current through your body is only about 9 microamps, far below what you can feel. The sense node sits at 9 V times the strap's resistance over the sum of that and 1 MΩ: a 1 MΩ strap reads about 4.5 V; a 10 MΩ strap about 8.2 V; an open strap 9 V; and a shorted one 0 V. The LM393 pair forms a window comparator that releases its open-collector outputs only when the node is between the lower limit near 4.1 V, about 0.8 MΩ, and the upper limit near 8.1 V, about 9 MΩ, so the green LED lights only for a good strap, and the red LED lights otherwise. Press the button while touching the metal pad with the strap on, and test daily before you work on electronics. Keep the tester battery-only and never connect it to mains or to mains earth.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| 1 MΩ across the test | Green |
| Open circuit | Red |
| Shorted | Red |
| A good strap on your wrist | Green |
If it does not work
Always red
Check the ladder voltages and the comparator pins.
Always green
Check the red LED wiring.
Dim LEDs
Check the pull-up and the series resistors.
Strap reads open
Clean the contacts and the wrist plate.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the ESD wrist strap tester?
Anti-static wrist strap, LM393 Comparator, Resistor 1 kΩ × 2, Resistor 1 MΩ × 2, LED 5 mm green, LED 5 mm red, Resistor 330 Ω × 2, Tactile push button 6 mm, 9 V battery, 9 V battery snap with DC jack, Resistor 10 kΩ × 6, Resistor 4.7 kΩ and Resistor 2 kΩ.
How long does the ESD wrist strap tester take to build?
About 60 minutes for a intermediate maker, in 7 steps.
How do I know the ESD wrist strap tester works?
1 MΩ across the test: Green. Open circuit: Red. Shorted: Red.
Always red: what should I check?
Check the ladder voltages and the comparator pins.
Always green: what should I check?
Check the red LED wiring.
Dim LEDs: what should I check?
Check the pull-up and the series resistors.
Strap reads open: what should I check?
Clean the contacts and the wrist plate.
