Projects / Electronic dice with a 7-segment display

Electronic dice with a 7-segment display

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 9 done
  1. UNO12:45

    Place the chip and display

    Put the CD4511 across the breadboard centre gap and the display next to it.

  2. UNO

    Wire the power

    Pin 16 to 5V, pin 8 to GND, and join pins 3 and 4 to 5V and pin 5 to GND.

  3. UNO

    Wire the number lines

    Pins 7, 1, 2 and 6 to Uno D2, D3, D4 and D5.

  4. UNO12:4512:45

    Wire the segments

    CD4511 outputs a to g each through a 330 ohm resistor to the matching display segment.

  5. UNO12:45

    Wire the display common

    The common pin of the display to GND.

  6. UNO

    Wire the button

    One leg to D8 and the other to GND.

  7. UNO

    Upload the sketch

    The display shows 0 and the monitor says Press the button to roll.

  8. UNO12:45

    Press and hold the button

    The digit rolls fast, slows down and stops on a number.

  9. UNO

    Release and press again

    Another number is chosen.

In short

How do you build an electronic dice with a 7-segment display?

Press the button and a single 7-segment digit rolls through numbers, slows down and settles on a random one to six. A CD4511 chip turns four wires into the seven segments, so you learn how decoders save pins. You need Arduino Uno R3, CD4511 BCD to 7-segment decoder, 7-segment display 1 digit (common cathode), Tactile push button 6 mm, Resistor 330 Ω × 7, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 9 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
CD4511 pin 16 VDD and pin 8 VSSUno 5V and GNDPower
CD4511 pin 3 LT and pin 4 BIUno 5VLamp test off, blanking off
CD4511 pin 5 LEUno GNDLatch always open so it follows the inputs
CD4511 pin 7 A, pin 1 B, pin 2 C, pin 6 DUno D2, D3, D4, D5The number in binary, A is the smallest bit
CD4511 outputs a b c d e f gPins 13, 12, 11, 10, 9, 15, 14, each through 330 ohms to the displayOne resistor per segment
Display common pinsUno GNDThis is a common cathode display
ButtonUno D8 and GNDPress to roll

Code

A seven-segment digit has seven lights, and driving it straight from the Uno would use seven pins. The CD4511 is a decoder that fixes that. You give it a number from 0 to 9 on four wires, written in binary, and it lights the right segments by itself. The four pins A, B, C and D carry the bits of the number with weights 1, 2, 4 and 8, so 5 is 0101, which is D low, C high, B low and A high. The sketch does exactly this in show(), taking one bit at a time from the number with a shift. The three control pins are tied so the chip is simply always on: LT is lamp test and BI is blanking, both are active low and are held high, while LE is the latch and is held low, so the outputs follow the inputs live. Each segment needs its own 330 ohm resistor, because the CD4511 outputs have no current limit. A roll shows random numbers fast, and the delay is made a little longer each time round, so the digit slows and settles, just like a tumbling die. The random numbers come from random(1, 7), which gives 1 to 6, and randomSeed() is fed from an unconnected analog pin, so the sequence is different on every start. The final value is printed to the serial monitor. Try adding a roll counter or a second digit, or stretch it to a 12 sided die by decoding two digits.

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t BCD_PINS[4] = {2, 3, 4, 5};   // A (1), B (2), C (4), D (8)
const uint8_t BTN = 8;

void show(uint8_t n) {
  for (uint8_t i = 0; i < 4; i++) {
    digitalWrite(BCD_PINS[i], (n >> i) & 1);   // one bit of the number per pin
  }
}

void setup() {
  for (uint8_t i = 0; i < 4; i++) pinMode(BCD_PINS[i], OUTPUT);
  pinMode(BTN, INPUT_PULLUP);
  Serial.begin(9600);
  randomSeed(analogRead(A0) + micros());          // an unconnected pin is a bit random
  show(0);
  Serial.println(F("Press the button to roll"));
}

void loop() {
  if (digitalRead(BTN) == LOW) {
    uint8_t value = 1;
    int wait = 40;
    while (wait < 400) {                          // roll quickly, then slow down
      value = random(1, 7);                       // 1 to 6
      show(value);
      delay(wait);
      wait += wait / 4 + 5;
    }
    show(value);
    Serial.print(F("Rolled "));
    Serial.println(value);
    while (digitalRead(BTN) == LOW) delay(10);    // wait for the button to be released
    delay(100);
  }
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Uno with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Press the button to roll

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power onThe display shows 0
Press the buttonDigits roll and then settle between 1 and 6
Roll 20 timesEvery number from 1 to 6 appears, and 0 or 7 never do
MonitorEach result is printed as Rolled and the number
Hold the button downIt rolls once and waits for release
Unplug the Uno and plug it in againA different first roll sequence

If it does not work

Display is blank

Check pin 4 BI is joined to 5V and the display common goes to GND.

Wrong digits

Swap the order of the four number wires, A must be the smallest bit on pin 7.

Digit shows odd shapes

The segment wires are in the wrong order, so check them against a to g.

Digit is dim

Use 220 ohm resistors instead of 330 ohm.

Same numbers every time

Keep randomSeed and leave A0 unconnected.

Button does nothing

Check it goes to D8 and GND.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the electronic dice with a 7-segment display?

Arduino Uno R3, CD4511 BCD to 7-segment decoder, 7-segment display 1 digit (common cathode), Tactile push button 6 mm, Resistor 330 Ω × 7, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the electronic dice with a 7-segment display take to build?

About 90 minutes for a beginner maker, in 9 steps.

How do I know the electronic dice with a 7-segment display works?

Power on: The display shows 0. Press the button: Digits roll and then settle between 1 and 6. Roll 20 times: Every number from 1 to 6 appears, and 0 or 7 never do.

Display is blank: what should I check?

Check pin 4 BI is joined to 5V and the display common goes to GND.

Wrong digits: what should I check?

Swap the order of the four number wires, A must be the smallest bit on pin 7.

Digit shows odd shapes: what should I check?

The segment wires are in the wrong order, so check them against a to g.

Digit is dim: what should I check?

Use 220 ohm resistors instead of 330 ohm.