Projects / Diode basics lab

Diode basics lab

Beginner30 minGuided buildReviewed

Build it step by step

0 of 6 done
  1. Test with the meter

    Set the meter to diode mode and put the red probe on the anode, black on the stripe. Note the reading, then reverse the probes.

  2. Compare the four diodes

    Record the forward reading of each in a table.

  3. 11.1 mA

    Light an LED through a diode

    Battery +, diode, 1 kΩ, LED, battery -. The LED lights.

  4. 11.2 mA

    Reverse the battery

    The LED stays off because the diode blocks.

  5. Measure the drop

    With the circuit on, measure across the diode and see how much voltage it uses.

  6. Use it for protection

    Place the diode in the positive supply of a small circuit so a reversed battery does no harm.

In short

How do you build a diode basics lab?

Test diodes in both directions, see the forward drop and use one for reverse-polarity protection. You need Rectifier Diode 1N4007 × 2, Signal Diode 1N4148, Schottky Diode 1N5819, LED 5 mm red, Resistor 1 kΩ, Digital multimeter, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack. It takes 6 steps and about 30 minutes.

Level
Beginner
Time
About 30 min
Parts
9
See the electronics first. This build uses AC rectifier. Try an AC rectifier in the circuit builder and watch the voltages and currents before you wire it.

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
9 V battery +Diode anode, then LED through 1 kΩSeries path
Diode cathode (stripe)1 kΩ then LED anodeForward direction
LED cathode9 V battery -Return
Meter in diode modeAcross each diodeReads the forward drop

No code needed

No code. A silicon diode like the 1N4007 or 1N4148 drops about 0.6 to 0.7 V, and a Schottky like the 1N5819 drops about 0.2 to 0.4 V. A diode in series with the supply stops a reversed battery from reaching the circuit.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
1N4007 forwardAbout 0.55 to 0.7 V on the meter
1N5819 SchottkyAbout 0.2 to 0.4 V
ReversedMeter shows OL (open)
Reversed batteryLED stays off

If it does not work

Reads zero both ways

The diode is shorted or you used the continuity mode. Use diode mode.

Reads OL both ways

The diode is open or the probes are not touching.

LED does not light

Check the LED direction and the diode direction.

Reading differs a lot from the table

Your meter's test current differs. Compare the diodes with each other.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the diode basics lab?

Rectifier Diode 1N4007 × 2, Signal Diode 1N4148, Schottky Diode 1N5819, LED 5 mm red, Resistor 1 kΩ, Digital multimeter, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack.

How long does the diode basics lab take to build?

About 30 minutes for a beginner maker, in 6 steps.

How do I know the diode basics lab works?

1N4007 forward: About 0.55 to 0.7 V on the meter. 1N5819 Schottky: About 0.2 to 0.4 V. Reversed: Meter shows OL (open).

Reads zero both ways: what should I check?

The diode is shorted or you used the continuity mode. Use diode mode.

Reads OL both ways: what should I check?

The diode is open or the probes are not touching.

LED does not light: what should I check?

Check the LED direction and the diode direction.

Reading differs a lot from the table: what should I check?

Your meter's test current differs. Compare the diodes with each other.