Projects / Coin-cell LED badge

Coin-cell LED badge

Beginner45 minGuided buildReviewed

Build it step by step

0 of 8 done
  1. 11.8 mA

    Calculate the resistor

    Voltage left divided by the LED current.

  2. ++11.8 mA

    Build it on the breadboard

    Cell, button, resistor, LED in a loop.

  3. 11.8 mA

    Press the button

    The LED lights.

  4. Measure the current

    Meter in series, in the milliamp range.

  5. Estimate the life

    Capacity divided by current.

  6. Try 220 ohm

    Compare the brightness.

  7. ++11.9 mA

    Plan the badge

    Draw where the cell, button and LED go.

  8. ++

    Make it safe

    Use a holder that grips the cell.

In short

How do you build a coin-cell LED badge?

A tiny badge with one LED and a push button, powered by a coin cell that lasts for weeks of short presses. You need CR2025 coin cell, CR2032 coin cell holder, LED 5 mm red, Resistor 1 kΩ, Tactile push button 6 mm and Breadboard 830 Tie Points. It takes 8 steps and about 45 minutes.

Level
Beginner
Time
About 45 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Coin cell holder plusButton leg 1A CR2032 has the same voltage and fits the holder better
Button leg 21 kohm resistorSeries resistor
1 kohm resistorLED anode (long leg)LED
LED cathode (short leg)Coin cell holder minusCloses the circuit

Code

This is a very simple wearable: a coin cell, a resistor, a red LED and a push button. A red LED needs about 1.8 volts, so a 3 volt cell leaves 1.2 volts across the resistor, and Ohm's law gives the current. A 1 kilohm resistor gives about 1.2 milliamps, which is dim but clear, and a 220 ohm resistor gives about five milliamps, which is brighter but drains the cell faster. Because the LED lights only while the button is pressed, a cell can last a very long time. A blue or white LED needs about 3 volts or more and may not light on a 3 volt cell at all. Coin cells are dangerous if swallowed, and can burn the throat in a short time, so keep this badge away from small children, use a holder that grips the cell, and never leave it where a pet might eat it. Never short the cell, heat it or try to recharge it. Add a layout on a piece of felt or card and sew or pin the badge on a bag, a hat or a school jumper.

No code. This is a simple circuit.

Choosing the resistor
Cell voltage:          about 3.0 V
Red LED drop:          about 1.8 V
Voltage left:          3.0 - 1.8 = 1.2 V
With 1 kohm:           1.2 / 1000 = 1.2 mA  (dim but clear)
With 220 ohm:          1.2 / 220  = 5.5 mA  (brighter, drains the cell faster)

Battery life
A coin cell holds roughly 150 mAh (CR2025) or 220 mAh (CR2032).
LED always on at 1.2 mA:  150 / 1.2 = about 125 hours
LED pressed 10 s a day:   1.2 mA x 10 s = tiny, the cell is limited by its shelf life, not the LED

Measure your own
Put the multimeter in series, in the current range, press the button and read the milliamps.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Press the buttonLED lights
ReleaseLED off
1 kohm resistorAbout 1.2 mA
220 ohm resistorAbout 5 mA
Blue LEDMay not light at 3 V

If it does not work

LED never lights

Check its direction, the long leg goes to the resistor.

Very dim

The cell may be flat, measure it, a good cell reads about 3 V.

Cell warm

Something is shorting it, remove it at once.

Blue or white LED does not light

It needs more than 3 V, use red or yellow.

Button feels stuck

Use a different button.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the coin-cell LED badge?

CR2025 coin cell, CR2032 coin cell holder, LED 5 mm red, Resistor 1 kΩ, Tactile push button 6 mm and Breadboard 830 Tie Points.

How long does the coin-cell LED badge take to build?

About 45 minutes for a beginner maker, in 8 steps.

How do I know the coin-cell LED badge works?

Press the button: LED lights. Release: LED off. 1 kohm resistor: About 1.2 mA.

LED never lights: what should I check?

Check its direction, the long leg goes to the resistor.

Very dim: what should I check?

The cell may be flat, measure it, a good cell reads about 3 V.

Cell warm: what should I check?

Something is shorting it, remove it at once.

Blue or white LED does not light: what should I check?

It needs more than 3 V, use red or yellow.