Projects / Slow blinker with a counter chip

Slow blinker with a counter chip

Beginner1 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. CD4060

    Power the chip

    5 V to pin 16 and GND to pin 8.

  2. Tie reset low

    Pin 12 to GND.

  3. CD4060

    Build the oscillator

    10 kohm and 100 nF to the junction, 100 kohm from the junction to pin 11.

  4. 15.4 mA

    Add the LED

    Pin 1 through 1 kohm to the LED, then GND.

  5. CD406015.4 mA

    Power up

    The LED changes state about every four and a half seconds.

  6. Measure

    Time ten changes with a stopwatch.

  7. CD406015.4 mA

    Move the LED

    Try pin 2 for a slower blink and pin 15 for a faster one.

  8. CD4060

    Change the capacitor

    Use 220 nF and note the new time.

In short

How do you build a slow blinker with a counter chip?

A chip with a built-in oscillator divides its frequency to blink an LED once every several seconds. You need CD4060 counter and oscillator, Resistor 100 kΩ, Resistor 10 kΩ, Ceramic Capacitor 100 nF, LED 5 mm red, Resistor 1 kΩ, Micro USB breakout board, 5 V 2 A USB adapter and Breadboard 830 Tie Points. It takes 8 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
9

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
CD4060 pin 16 (VDD)5 V from the USB breakoutPower
CD4060 pin 8 (VSS)GNDGround
CD4060 pin 12 (RESET)GNDMust be low or the counter stays at zero
10 kohm resistorPin 10 to a junction JTiming resistor
100 nF capacitorPin 9 to the junction JTiming capacitor
100 kohm resistorJunction J to pin 11Series resistor, larger than the timing resistor
LED plus through 1 kohmPin 1 (Q12)Divided output, about nine seconds a cycle
LED minusGNDCommon ground

Code

The CD4060 contains an oscillator and a fourteen-stage binary counter in one chip. You set the oscillator speed with one resistor and one capacitor, and each output pin gives the clock divided by a different power of two. Slow outputs let you get blinks that last several seconds with no microcontroller and very little power. The oscillator needs three connections: the timing resistor, the timing capacitor and a larger series resistor, joined at one junction. The reset pin must be tied to ground, otherwise the counter is held at zero and the outputs never change. The outputs of this CMOS chip are weak, so use a 1 kilohm resistor for the LED, which makes it a little dim but safe for the chip. Because the frequency depends on the capacitor value, which is usually only accurate to 10 or 20 percent, the blink times are approximate. Change the capacitor or the resistor to speed it up or slow it down, or move the LED to a different output pin.

No code. This is a hardware-only circuit. The notes below are your build sheet.

Oscillator frequency is about 1 / (2.2 x Rt x Ct).
With Rt = 10 kohm and Ct = 100 nF that is about 455 Hz.
Each output divides the clock by a power of two:

Pin  Output  Divide by  Time for one full cycle (about)
7    Q4      16         0.035 s
5    Q5      32         0.07 s
4    Q6      64         0.14 s
6    Q7      128        0.28 s
14   Q8      256        0.56 s
13   Q9      512        1.1 s
15   Q10     1024       2.3 s
1    Q12     4096       9 s
2    Q13     8192       18 s
3    Q14     16384      36 s

An LED on a given output is on for half of that time and off for half.
Real chips and capacitors vary by 20 percent or more, so measure with a stopwatch.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
LED on pin 1Changes about every 4.5 s
LED on pin 15Changes about every 1.1 s
Double the capacitorRoughly double the time
Reset pin liftedOutput holds at zero
Remove the series resistorOscillator may not start

If it does not work

LED never changes

Reset on pin 12 must go to GND.

Fast flicker instead of slow

You are on a low-numbered output, use pin 1, 2 or 3.

Oscillator does not run

Check the junction and the order of pins 9, 10 and 11.

LED very dim

Normal at 5 V with a 1 kohm resistor.

Times far off

The capacitor value differs from the label, measure and adjust.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the slow blinker with a counter chip?

CD4060 counter and oscillator, Resistor 100 kΩ, Resistor 10 kΩ, Ceramic Capacitor 100 nF, LED 5 mm red, Resistor 1 kΩ, Micro USB breakout board, 5 V 2 A USB adapter and Breadboard 830 Tie Points.

How long does the slow blinker with a counter chip take to build?

About 60 minutes for a beginner maker, in 8 steps.

How do I know the slow blinker with a counter chip works?

LED on pin 1: Changes about every 4.5 s. LED on pin 15: Changes about every 1.1 s. Double the capacitor: Roughly double the time.

LED never changes: what should I check?

Reset on pin 12 must go to GND.

Fast flicker instead of slow: what should I check?

You are on a low-numbered output, use pin 1, 2 or 3.

Oscillator does not run: what should I check?

Check the junction and the order of pins 9, 10 and 11.

LED very dim: what should I check?

Normal at 5 V with a 1 kohm resistor.