Projects / Model bus stop request sign

Model bus stop request sign

Beginner50 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Wire the three request buttons

    D2, D3 and D4 to GND.

  2. NANO

    Wire the reset button

    D5 to GND.

  3. NANO12.0 mA

    Wire the two LEDs and the buzzer

    D8, D9 and D10.

  4. NANO

    Upload and open the serial monitor at 9600

    It says Ready.

  5. NANO

    Press any request button

    Both lamps light and one chime plays.

  6. NANO

    Press the other request buttons

    Nothing more happens.

  7. NANO

    Press reset

    The sign clears.

In short

How do you build a model bus stop request sign?

A row of request buttons along a toy bus lights a Stopping sign and rings a soft chime once, as on a real bus. A reset button clears it when the bus stops. A friendly model for learning about latching signals. You need Arduino Nano, Tactile push button 6 mm × 4, LED 5 mm red × 2, Resistor 220 Ω × 2, Passive buzzer, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 50 minutes.

Level
Beginner
Time
About 50 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Request button 1Nano D2 and GNDPressing joins D2 to ground
Request button 2Nano D3 and GNDPressing joins D3 to ground
Request button 3Nano D4 and GNDPressing joins D4 to ground
Reset button (driver)Nano D5 and GNDPressing joins D5 to ground
Stopping sign LED long legNano D8 through a 220 ohm resistor, short leg to GNDThe passengers' sign
Driver lamp LED long legNano D9 through a 220 ohm resistor, short leg to GNDThe driver's lamp
Passive buzzer + and -Nano D10 and GNDThe chime

Code

On a bus, the first passenger to press a stop button lights a sign for everybody, and more presses do nothing until the bus has stopped. In programming terms the sign is latched: once it turns on it stays on by itself. The sketch has two states, waiting and stopping. In the waiting state it looks at the three request buttons, and the first press lights the passenger sign and the driver's lamp and plays one two-note chime. In the stopping state it ignores the request buttons and watches only the driver's reset button. Test it with all three buttons pressed together and listen for just one chime. This is a model for learning about latches and states. Think about what else a real bus does, such as a wheelchair request that uses a different chime, and try adding it with a fourth request button.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t REQUEST_PINS[3] = {2, 3, 4};
const uint8_t RESET_PIN = 5;
const uint8_t SIGN_LED = 8;
const uint8_t DRIVER_LED = 9;
const uint8_t BUZZER_PIN = 10;

bool stopping = false;

void chime() {                               // a soft two-note ding-dong
  tone(BUZZER_PIN, 880, 200);
  delay(250);
  tone(BUZZER_PIN, 660, 300);
  delay(350);
}

void setup() {
  for (int i = 0; i < 3; i++) pinMode(REQUEST_PINS[i], INPUT_PULLUP);
  pinMode(RESET_PIN, INPUT_PULLUP);
  pinMode(SIGN_LED, OUTPUT);
  pinMode(DRIVER_LED, OUTPUT);
  pinMode(BUZZER_PIN, OUTPUT);
  Serial.begin(9600);
  Serial.println("Ready.");
}

void loop() {
  if (!stopping) {
    for (int i = 0; i < 3; i++) {
      if (digitalRead(REQUEST_PINS[i]) == LOW) {   // the first press latches the sign
        stopping = true;
        digitalWrite(SIGN_LED, HIGH);
        digitalWrite(DRIVER_LED, HIGH);
        chime();                                    // only one chime, however many presses
        Serial.print("Stop requested from button ");
        Serial.println(i + 1);
        break;
      }
    }
  } else if (digitalRead(RESET_PIN) == LOW) {       // the driver clears it
    stopping = false;
    digitalWrite(SIGN_LED, LOW);
    digitalWrite(DRIVER_LED, LOW);
    Serial.println("Sign cleared.");
    delay(300);
  }
  delay(20);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Ready.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
WaitingBoth lamps off
First requestLamps on and a single chime
More requestsIgnored
Reset buttonLamps off, ready again
Serial monitorNames the button that was pressed

If it does not work

No chime

Check you have a passive buzzer on D10.

Chime plays more than once

Check the latch logic, buttons should be ignored while stopping.

Sign never clears

Check the reset button goes to D5 and GND.

LED stays dark

Check its direction and its resistor.

Nothing happens at all

Check each button goes to its pin and GND.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the model bus stop request sign?

Arduino Nano, Tactile push button 6 mm × 4, LED 5 mm red × 2, Resistor 220 Ω × 2, Passive buzzer, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the model bus stop request sign take to build?

About 50 minutes for a beginner maker, in 7 steps.

How do I know the model bus stop request sign works?

Waiting: Both lamps off. First request: Lamps on and a single chime. More requests: Ignored.

No chime: what should I check?

Check you have a passive buzzer on D10.

Chime plays more than once: what should I check?

Check the latch logic, buttons should be ignored while stopping.

Sign never clears: what should I check?

Check the reset button goes to D5 and GND.

LED stays dark: what should I check?

Check its direction and its resistor.