Projects / 8-step sequencer synth

8-step sequencer synth

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANOCD4051

    Test the pots

    Read each one directly with analogRead.

  2. NANO

    Add the 4051

    Select channels and print the readings.

  3. NANO14.9 mA

    Add the LEDs

    Light one LED per step.

  4. NANO

    Map pots to notes

    Use the pentatonic scale.

  5. NANO

    Add the tempo pot

    Change the step length.

  6. NANO

    Add the button

    Start and stop.

  7. NANO

    Label the knobs

    Number the steps 1 to 8.

In short

How do you build a 8-step sequencer synth?

Eight pots set the pitch of eight steps, an Arduino plays them in a loop with LEDs, and a tempo knob sets the speed. You need Arduino Nano, Potentiometer 10 kΩ × 9, LED 5 mm red × 8, Resistor 220 Ω × 8, CD4051 analog multiplexer, Passive buzzer, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
9

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
CD4051 pin 16 (VCC)Nano 5VPower
CD4051 pin 8 (VSS) and pin 7 (VEE)Nano GNDGround and negative supply
CD4051 pin 6 (INH)Nano GNDAlways enabled
CD4051 pins 11, 10, 9 (A, B, C)Nano D2, D3, D4Channel select
CD4051 pin 3 (COM)Nano A0Analogue input
CD4051 pins 13, 14, 15, 12, 1, 5, 2, 4 (X0 to X7)Wipers of pots 1 to 8Eight step pitches
Each pot's ends5 V and GNDPot supply
Ninth pot wiperNano A2Tempo
LEDs 1 to 8 with 220 ΩNano D5 to D12 and GNDStep lights
Passive buzzer +Nano A1Sound (− to GND)
ButtonNano D13 and GNDStart and stop

Code

The CD4051 is an analogue multiplexer: three address pins choose which of eight pots connects to the single output at pin 3, so one analogue input on the Nano reads all eight knobs. The VEE pin is the negative supply and goes to ground here because the signals are only 0 to 5 V. Mapping the pot range onto a pentatonic scale means any setting sounds musical. The tempo pot sets the step length from 80 ms to 600 ms. A passive buzzer plays a clean square tone; to hear more, connect the buzzer pin through a 1 kΩ resistor and a small capacitor to an amplifier's input. Keep the pots' ends on 5 V and ground and the wipers on the 4051 inputs, or the readings will jump. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// 8-step sequencer. Board: Arduino Nano. No libraries.
const byte SEL[3] = {2, 3, 4};                 // 4051 address pins A, B, C
const byte LED[8] = {5, 6, 7, 8, 9, 10, 11, 12};
const int BUZZ = A1, BTN = 13;
// Pentatonic scale, frequencies in Hz across two octaves (15 notes plus a rest at the bottom).
const int NOTES[15] = {131, 147, 165, 196, 220, 262, 294, 330, 392, 440, 523, 587, 659, 784, 880};
bool running = true; unsigned long lastBtn = 0;

int readStep(byte ch) {
  for (byte b = 0; b < 3; b++) digitalWrite(SEL[b], (ch >> b) & 1);
  delayMicroseconds(50);                        // let the multiplexer settle
  return analogRead(A0);
}

void setup() {
  for (byte i = 0; i < 3; i++) pinMode(SEL[i], OUTPUT);
  for (byte i = 0; i < 8; i++) pinMode(LED[i], OUTPUT);
  pinMode(BTN, INPUT_PULLUP);
}

void loop() {
  for (byte s = 0; s < 8; s++) {
    if (!digitalRead(BTN) && millis() - lastBtn > 300) { running = !running; lastBtn = millis(); }
    if (!running) { noTone(BUZZ); for (byte i = 0; i < 8; i++) digitalWrite(LED[i], LOW); delay(50); s = 7; continue; }
    for (byte i = 0; i < 8; i++) digitalWrite(LED[i], i == s);
    int pot = readStep(s);                      // 0 to 1023
    int note = map(pot, 0, 1023, 0, 14);
    int stepMs = map(analogRead(A2), 0, 1023, 80, 600);      // tempo: step length in milliseconds
    tone(BUZZ, NOTES[note], stepMs * 8 / 10);   // note lasts 80 percent of the step, then a short gap
    delay(stepMs);
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Turn a potThat step's pitch changes
LEDsA light runs along the eight steps
Tempo knobFaster and slower loop
ButtonStops and starts the sequence

If it does not work

Pots interfere

Check the INH pin goes to ground and the pot ends are on 5 V and GND.

Wrong step order

Check the A, B, C pins against the X0 to X7 order.

Quiet sound

Use a passive buzzer and a short wire.

Notes click

Lengthen the gap between notes.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the 8-step sequencer synth?

Arduino Nano, Potentiometer 10 kΩ × 9, LED 5 mm red × 8, Resistor 220 Ω × 8, CD4051 analog multiplexer, Passive buzzer, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the 8-step sequencer synth take to build?

About 150 minutes for a intermediate maker, in 7 steps.

How do I know the 8-step sequencer synth works?

Turn a pot: That step's pitch changes. LEDs: A light runs along the eight steps. Tempo knob: Faster and slower loop.

Pots interfere: what should I check?

Check the INH pin goes to ground and the pot ends are on 5 V and GND.

Wrong step order: what should I check?

Check the A, B, C pins against the X0 to X7 order.

Quiet sound: what should I check?

Use a passive buzzer and a short wire.

Notes click: what should I check?

Lengthen the gap between notes.