Bluetooth home automation with four relays
Build it step by step
0 of 5 doneWire the HC-05
TXD to D2, D3 to RXD through the 1 kΩ / 2.2 kΩ divider, VCC and GND.
Wire the relay board
VCC, GND and IN1 to IN4 to D4 to D7.
Add a safe load
Switch a 12 V LED strip through relay 1 (COM to adapter plus, NO to strip plus).
Upload and pair
Upload, pair the phone with HC-05 and connect from a serial terminal app.
Box it
Mount everything in the project box with the low-voltage side away from the relay contacts.
How do you build a bluetooth home automation with four relays?
Switch four loads on and off from a phone over Bluetooth using an HC-05 and a 4-channel relay board. You need Arduino Uno R3, HC-05 Bluetooth Module, Relay module 4-channel 5 V, Resistor 1 kΩ, Resistor 2.2 kΩ, 12 V LED strip warm white (5 m, 2835), 12 V 2 A DC adapter, DC barrel to screw terminal adapter (female), ABS project box (100 × 60 × 25 mm) and Jumper wires female to female (40 pcs). It takes 5 steps and about 90 minutes.
- Level
- Intermediate
- Time
- About 90 min
- Parts
- 10
Parts list
- Development BoardsBuyArduino Uno R3 × 1
- WirelessBuy
- InterfacesBuy
- PassivesBuyResistor 1 kΩ × 1
- PassivesBuyResistor 2.2 kΩ × 1
- OptoelectronicsBuyPractise with 12 V loads first
- PowerBuy
- PowerBuy
- Mechanical & HardwareBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| HC-05 TXD | Uno D2 | Commands from the phone |
| Uno D3 | 1 kΩ to HC-05 RXD, 2.2 kΩ from RXD to GND | Replies, divided to 3.3 V logic |
| Relay board VCC / GND | Uno 5V / GND | Relay coils |
| Relay IN1 / IN2 / IN3 / IN4 | Uno D4 / D5 / D6 / D7 | One pin per relay |
| 12 V adapter + | Relay 1 COM; relay 1 NO to LED strip + | Practice load switched by relay 1 |
| LED strip − | 12 V adapter − | Load return |
Code
Arduino IDE, board "Arduino Uno". Use any Bluetooth serial terminal app: send 1 to 4 to switch on, a to d to switch off, 0 for all off and ? for the status.
Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).
#include <SoftwareSerial.h>
SoftwareSerial bt(2, 3);
const int RELAY[4] = {4, 5, 6, 7};
const bool ON = LOW; // most relay boards are active-low
bool state[4] = {false, false, false, false};
void apply() { for (int i = 0; i < 4; i++) digitalWrite(RELAY[i], state[i] ? ON : !ON); }
void report() {
for (int i = 0; i < 4; i++) { bt.print("Relay "); bt.print(i + 1); bt.println(state[i] ? ": ON" : ": OFF"); }
}
void setup() {
for (int i = 0; i < 4; i++) pinMode(RELAY[i], OUTPUT);
apply();
bt.begin(9600);
}
void loop() {
if (!bt.available()) return;
char c = bt.read();
if (c >= '1' && c <= '4') state[c - '1'] = true; // 1-4 switch on
else if (c >= 'a' && c <= 'd') state[c - 'a'] = false; // a-d switch off
else if (c == '0') for (bool &s : state) s = false; // all off
else if (c == '?') { report(); return; }
else return;
apply();
report();
}Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Send ? | Four status lines, all OFF |
| Send 1 | Relay 1 clicks, its LED lights, the LED strip turns on |
| Send a | Relay 1 releases, strip off |
| Send 0 | All relays off |
If it does not work
Relays switch the opposite way
Your board is active-high. Change ON to HIGH.
Relays chatter or the Uno resets
Four coils draw about 300 mA. Power the relay board's JD-VCC from a separate 5 V supply and remove its jumper.
Phone shows nothing back
Check the D3 divider goes to HC-05 RXD.
Mains loads
Mains wiring must be done by a qualified electrician in a closed, earthed box with fuses. Learn with 12 V loads.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the bluetooth home automation with four relays?
Arduino Uno R3, HC-05 Bluetooth Module, Relay module 4-channel 5 V, Resistor 1 kΩ, Resistor 2.2 kΩ, 12 V LED strip warm white (5 m, 2835), 12 V 2 A DC adapter, DC barrel to screw terminal adapter (female), ABS project box (100 × 60 × 25 mm) and Jumper wires female to female (40 pcs). 12 V LED strip warm white (5 m, 2835): Practise with 12 V loads first.
How long does the bluetooth home automation with four relays take to build?
About 90 minutes for a intermediate maker, in 5 steps.
How do I know the bluetooth home automation with four relays works?
Send ?: Four status lines, all OFF. Send 1: Relay 1 clicks, its LED lights, the LED strip turns on. Send a: Relay 1 releases, strip off.
Relays switch the opposite way: what should I check?
Your board is active-high. Change ON to HIGH.
Relays chatter or the Uno resets: what should I check?
Four coils draw about 300 mA. Power the relay board's JD-VCC from a separate 5 V supply and remove its jumper.
Phone shows nothing back: what should I check?
Check the D3 divider goes to HC-05 RXD.
Mains loads: what should I check?
Mains wiring must be done by a qualified electrician in a closed, earthed box with fuses. Learn with 12 V loads.
