Transistor saturation and base resistor lab
Build it step by step
0 of 7 doneWire the load
Battery plus, the 470 ohm resistor, the LED, the BC547 collector.
Wire the emitter
BC547 emitter to battery minus.
Add the 1 megohm base resistor
From battery plus to the base.
Measure Vce
Note the collector voltage and how bright the LED is.
Swap in 100 kilohms, 10 kilohms and 1 kilohm in turn
Measure Vce each time.
Work out the base current
About 8.3 V divided by the base resistor.
Write a rule
Choose a base current of about a tenth of the collector current.
How do you build a transistor saturation and base resistor lab?
Switch a red LED with a BC547 and four different base resistors, and measure the voltage left across the transistor each time. Too little base current leaves it half on and wasting power, and a smaller resistor saturates it. You need BC547 NPN transistor, Resistor 1 MΩ, Resistor 100 kΩ, Resistor 10 kΩ, Resistor 1 kΩ, LED 5 mm red, Resistor 470 Ω, Digital multimeter, 9 V battery, 9 V battery snap with DC jack, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 50 minutes.
- Level
- Beginner
- Time
- About 50 min
- Parts
- 12
Parts list
- SemiconductorsBuy
- PassivesBuyResistor 1 MΩ × 1
- PassivesBuyResistor 100 kΩ × 1
- PassivesBuyResistor 10 kΩ × 1
- PassivesBuyResistor 1 kΩ × 1
- SemiconductorsBuyLED 5 mm red × 1
- PassivesBuyResistor 470 Ω × 1
- Tools & InstrumentsBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
- PrototypingBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Battery plus | LED long leg through the 470 ohm resistor | Load supply |
| LED short leg | BC547 collector | Load switched by the transistor |
| BC547 emitter | Battery minus | Common ground |
| Battery plus | Base resistor leg 1 | Always-on base drive |
| Base resistor leg 2 | BC547 base | Sets the base current |
| Meter red probe | BC547 collector | Measures the voltage across the transistor |
| Meter black probe | BC547 emitter and battery minus | Reference |
No code needed
No code. A transistor used as a switch should be driven so hard that the voltage across it falls to about 0.1 to 0.2 V, which is called saturation, so it wastes almost no power. The collector current here is about 14 mA, set by the LED and its 470 ohm resistor. The base current is about 8.3 volts divided by the base resistor. With 1 megohm it is only about 8 microamps, which is too little, so the transistor is half on, the LED is dim and the collector sits at several volts. With 100 kilohms it is about 83 microamps and the transistor is close to saturation. With 10 kilohms and 1 kilohm it is hard on and Vce is about 0.1 V. A common rule is to give the base about a tenth of the collector current. Gains vary from one transistor to another, so your numbers will differ. Keep to the 9 V battery and do not use a smaller base resistor than 1 kilohm.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| 1 megohm | Vce of several volts and a dim LED |
| 100 kilohms | Vce under about 1 V, LED fairly bright |
| 10 kilohms | Vce about 0.1 to 0.2 V, LED bright |
| 1 kilohm | Vce about 0.1 V, no further change |
| Base current for 10 kilohms | About 0.8 mA |
If it does not work
LED never lights
Check the transistor pins: flat face, then collector, base, emitter from the left on most BC547s.
LED always bright
The base resistor is too small, or the base is touching the supply.
Vce looks stuck at 9 V
The base resistor may not be connected to the base.
Transistor gets hot
Stop and recheck, since the load should be only about 14 mA.
Readings vary
Gain differs between transistors, so test your own.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the transistor saturation and base resistor lab?
BC547 NPN transistor, Resistor 1 MΩ, Resistor 100 kΩ, Resistor 10 kΩ, Resistor 1 kΩ, LED 5 mm red, Resistor 470 Ω, Digital multimeter, 9 V battery, 9 V battery snap with DC jack, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).
How long does the transistor saturation and base resistor lab take to build?
About 50 minutes for a beginner maker, in 7 steps.
How do I know the transistor saturation and base resistor lab works?
1 megohm: Vce of several volts and a dim LED. 100 kilohms: Vce under about 1 V, LED fairly bright. 10 kilohms: Vce about 0.1 to 0.2 V, LED bright.
LED never lights: what should I check?
Check the transistor pins: flat face, then collector, base, emitter from the left on most BC547s.
LED always bright: what should I check?
The base resistor is too small, or the base is touching the supply.
Vce looks stuck at 9 V: what should I check?
The base resistor may not be connected to the base.
Transistor gets hot: what should I check?
Stop and recheck, since the load should be only about 14 mA.
