Projects / Bicycle speedometer and odometer

Bicycle speedometer and odometer

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANOA3144

    Mount the sensor

    Fix the A3144 on the fork leg so the magnet on a spoke passes within 5 mm of its flat face.

  2. NANO

    Fix the magnet

    Glue or tape a magnet to a spoke, south pole facing the sensor. If nothing is detected, flip the magnet.

  3. NANO

    Wire the sensor

    VCC to 5V, GND to GND, OUT to D2 with a 10 kΩ pull-up to 5V.

  4. NANO

    Wire the display

    SDA to A4, SCL to A5, VCC to 5V, GND to GND.

  5. NANOTP4056MT3608

    Power it

    Li-Po into the TP4056 for charging, TP4056 output through a switch to the MT3608 set to 5.0 V, then to the Nano. Never connect a boost output until it is set.

  6. NANO

    Calibrate

    Ride 1 km (use a phone map) and compare the trip distance. Adjust WHEEL_MM in proportion.

In short

How do you build a bicycle speedometer and odometer?

A hall sensor and a magnet on a spoke measure each wheel turn, so an OLED can show speed, trip distance, trip time and a saved odometer. You need Arduino Nano, Hall Effect Sensor A3144, Neodymium magnets (10 × 3 mm), SSD1306 OLED Display, Resistor 10 kΩ, Li-Po battery 3.7 V 1000 mAh, TP4056 Charging Module, MT3608 Boost Module and ABS project box (100 × 60 × 25 mm). It takes 6 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
9

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
A3144 pin 1 (VCC) / pin 2 (GND)Nano 5V / GNDSensor power (flat face towards you, pins down)
A3144 pin 3 (OUT)Nano D2Pulse for each wheel turn
10 kΩ between A3144 OUT and 5VPull-upOpen-collector output needs it
OLED SDA / SCLNano A4 / A5Display
OLED VCC / GNDNano 5V / GNDPower
Li-Po through TP4056 OUT, then MT3608 set to 5.0 VNano 5V / GNDPortable power, with a switch in the Li-Po feed

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install Adafruit SSD1306 and Adafruit GFX. Set WHEEL_MM from your wheel: roll it one full turn on the ground and measure.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
#include <EEPROM.h>

Adafruit_SSD1306 d(128, 64, &Wire, -1);
const float WHEEL_MM = 2105.0;                // 700x25c road wheel; measure yours by rolling it one turn
volatile unsigned long lastPulse = 0, period = 0;
volatile unsigned long revs = 0;
unsigned long tripRevs = 0, moveMs = 0, lastDraw = 0, savedRevs;

void onPulse() {
  unsigned long now = millis();
  if (now - lastPulse > 25) { period = now - lastPulse; lastPulse = now; revs++; }   // 25 ms debounce
}

void setup() {
  pinMode(2, INPUT);
  attachInterrupt(digitalPinToInterrupt(2), onPulse, FALLING);
  d.begin(SSD1306_SWITCHCAPVCC, 0x3C);
  EEPROM.get(0, savedRevs);
  if (savedRevs == 0xFFFFFFFFUL) savedRevs = 0;
}

void loop() {
  noInterrupts();
  unsigned long p = period, lp = lastPulse, r = revs;
  interrupts();

  float kmh = 0;
  if (millis() - lp < 3000 && p > 0) kmh = (WHEEL_MM / 1000.0) / (p / 1000.0) * 3.6;   // metres per second to km/h
  static unsigned long lastR = 0, lastT = 0;
  if (r != lastR) { tripRevs += r - lastR; lastR = r; }
  if (kmh > 0) moveMs += millis() - lastT;
  lastT = millis();
  if (r - savedRevs >= 250 && millis() - lp > 3000) { savedRevs = r; EEPROM.put(0, savedRevs); }   // save when stopped

  if (millis() - lastDraw > 250) {
    lastDraw = millis();
    float tripKm = tripRevs * WHEEL_MM / 1000000.0;
    unsigned long s = moveMs / 1000;
    d.clearDisplay(); d.setTextColor(WHITE);
    d.setTextSize(3); d.setCursor(0, 0); d.print(kmh, 1);
    d.setTextSize(1); d.setCursor(90, 14); d.print("km/h");
    d.setCursor(0, 32); d.print("Trip "); d.print(tripKm, 2); d.print(" km");
    d.setCursor(0, 44); d.print("Time "); d.print(s / 60); d.print(":"); if (s % 60 < 10) d.print("0"); d.print(s % 60);
    d.setCursor(0, 56); d.print("ODO "); d.print((savedRevs + (r - savedRevs)) * WHEEL_MM / 1000000.0, 1); d.print(" km");
    d.display();
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Spin the wheel by handSpeed shows a value and falls to 0.0 about three seconds after you stop
Ride at a steady 20 km/hDisplay shows near 20.0 km/h
Ride 1 kmTrip shows about 1.00 km after calibration
Switch off and onODO keeps its value, saved every 250 turns while stopped

If it does not work

Speed reads zero while turning

The magnet is too far or the wrong pole faces the sensor. Flip it and bring it to 3 mm.

Speed is double or half

Two magnets or a missed pulse. Check mounting, or change WHEEL_MM only after fixing that.

Display glitches on bumps

Secure the wires and add a 100 nF capacitor at the display.

The sensor chip gets hot

It is in backwards. Check pin 1 is VCC and the flat face is towards the magnet.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the bicycle speedometer and odometer?

Arduino Nano, Hall Effect Sensor A3144, Neodymium magnets (10 × 3 mm), SSD1306 OLED Display, Resistor 10 kΩ, Li-Po battery 3.7 V 1000 mAh, TP4056 Charging Module, MT3608 Boost Module and ABS project box (100 × 60 × 25 mm).

How long does the bicycle speedometer and odometer take to build?

About 90 minutes for a beginner maker, in 6 steps.

How do I know the bicycle speedometer and odometer works?

Spin the wheel by hand: Speed shows a value and falls to 0.0 about three seconds after you stop. Ride at a steady 20 km/h: Display shows near 20.0 km/h. Ride 1 km: Trip shows about 1.00 km after calibration.

Speed reads zero while turning: what should I check?

The magnet is too far or the wrong pole faces the sensor. Flip it and bring it to 3 mm.

Speed is double or half: what should I check?

Two magnets or a missed pulse. Check mounting, or change WHEEL_MM only after fixing that.

Display glitches on bumps: what should I check?

Secure the wires and add a 100 nF capacitor at the display.

The sensor chip gets hot: what should I check?

It is in backwards. Check pin 1 is VCC and the flat face is towards the magnet.