Lab / KTU / Circuits and measurements / Experiment 9

RC low-pass and high-pass filters

Circuits and measurementsVirtual readings4 viva questionsRecord book ready
Open virtual bench
Aim

To plot the frequency response of first-order RC low-pass and high-pass filters and find the cut-off frequency.

Apparatus
  • Function generator
  • Resistor 1 kΩ
  • Capacitor 0.1 µF
  • CRO

Theory

An RC low-pass filter passes low frequencies: gain = 1/√(1 + (f/fc)²). A high-pass filter does the opposite: gain = (f/fc)/√(1 + (f/fc)²). At the cut-off frequency fc = 1/(2πRC) the gain is 0.707 (−3 dB), and beyond it the response falls by 20 dB per decade.

Read the lesson: Capacitors inductors ›
Circuit connections
  • Low-pass: input → R → output node, C from output to ground
  • High-pass: input → C → output node, R from output to ground

Procedure

Pre-lab check

4 questions · 75% to be ready
1Why is fc called the −3 dB point?
2What is the roll-off of a first-order filter?
3Why are they called passive filters?
4Where is a low-pass filter used?

Try the readings before the lab

Calculated, not measured. In the lab, write down your own readings.
fc = 1 / (2πRC)1.59 kHz
-37-27-17-7.142.72322261.6k11.3k79.6kf (Hz, log)Gain (dB)
f (Hz)Vo / ViGain (dB)
3210
850.9990
2250.99-0.1
5990.936-0.6
15920.707-3
42320.352-9.1
112540.14-17.1
299260.053-25.5
795770.02-34

Precautions

  • Keep the input amplitude constant.
  • Use a log scale for frequency.

My readings

Type what you measured. It goes into your record book, and to My Garage when you are signed in.

S. No.f (Hz)Vo / ViGain (dB)
1
2
3
4
5
6

Check my readings

Put the value you set in the first column, then compare. Real parts have tolerance.

Open my record book
Result

The cut-off frequency is ___ Hz (theory ___ Hz); the gain falls at about 20 dB/decade beyond it.

Everything above is free. The print-ready write-up comes with Maker.

Printed pages leave the observation table empty for your own readings.

Viva questions

Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.

1. Why is fc called the −3 dB point?
2. What is the roll-off of a first-order filter?
3. Why are they called passive filters?
4. Where is a low-pass filter used?

Quick answers for your record and viva

What is the aim of the rc low-pass and high-pass filters experiment?

To plot the frequency response of first-order RC low-pass and high-pass filters and find the cut-off frequency.

What apparatus is needed for rc low-pass and high-pass filters?

Function generator, Resistor 1 kΩ, Capacitor 0.1 µF, CRO.

What is the theory behind rc low-pass and high-pass filters?

An RC low-pass filter passes low frequencies: gain = 1/√(1 + (f/fc)²). A high-pass filter does the opposite: gain = (f/fc)/√(1 + (f/fc)²). At the cut-off frequency fc = 1/(2πRC) the gain is 0.707 (−3 dB), and beyond it the response falls by 20 dB per decade.

What result should I get in rc low-pass and high-pass filters?

The cut-off frequency is ___ Hz (theory ___ Hz); the gain falls at about 20 dB/decade beyond it.

What precautions should I take in rc low-pass and high-pass filters?

Keep the input amplitude constant. Use a log scale for frequency.

RC low-pass and high-pass filters: lab experiment and viva