Lab / GTU / Analog and linear ICs / Experiment 6

Active low-pass, high-pass and band-pass filters

Analog and linear ICsVirtual readings4 viva questionsRecord book ready
Open virtual bench
Aim

To design first-order active low-pass and high-pass filters with an op-amp and plot their frequency response.

Apparatus
  • IC 741
  • Resistors
  • Capacitors 0.01 µF
  • Dual supply ±12 V
  • Function generator
  • CRO

Theory

An RC network followed by a non-inverting amplifier gives a first-order active filter with cut-off fc = 1/(2πRC) and pass-band gain Af = 1 + Rf/R1. Unlike a passive filter, it can have gain and drives a load without changing its response. A band-pass filter can be made by cascading a high-pass and a low-pass section with fL < fH.

Circuit connections
  • Low-pass: input → R → pin 3, C from pin 3 to ground; R1 from pin 2 to ground, Rf from pin 2 to pin 6
  • High-pass: swap R and C at the input

Procedure

Pre-lab check

4 questions · 75% to be ready
1Advantages of active filters over passive ones?
2What is a Butterworth response?
3What is the roll-off of a second-order filter?
4Limitation of active filters?

Try the readings before the lab

Calculated, not measured. In the lab, write down your own readings.
fc1 kHz
Pass-band gain6 dB
-26-17-8.75-0.28.36331819955.5k30.0kf (Hz, log)Gain (dB)
f (Hz)GainGain (dB)
331.9996
781.9946
1831.9675.9
4281.8395.3
10011.4143
23430.786-2.1
54830.359-8.9
128310.156-16.2
300290.067-23.5

Precautions

  • Keep the input amplitude constant and below clipping.
  • Use the nearest standard resistor and note the change in fc.

My readings

Type what you measured. It goes into your record book, and to My Garage when you are signed in.

S. No.f (Hz)GainGain (dB)
1
2
3
4
5
6

Check my readings

Put the value you set in the first column, then compare. Real parts have tolerance.

Open my record book
Result

fc = ___ Hz (design 1 kHz), pass-band gain = ___ dB, roll-off ≈ 20 dB/decade.

Everything above is free. The print-ready write-up comes with Maker.

Printed pages leave the observation table empty for your own readings.

Viva questions

Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.

1. Advantages of active filters over passive ones?
2. What is a Butterworth response?
3. What is the roll-off of a second-order filter?
4. Limitation of active filters?

Quick answers for your record and viva

What is the aim of the active low-pass, high-pass and band-pass filters experiment?

To design first-order active low-pass and high-pass filters with an op-amp and plot their frequency response.

What apparatus is needed for active low-pass, high-pass and band-pass filters?

IC 741, Resistors, Capacitors 0.01 µF, Dual supply ±12 V, Function generator, CRO.

What is the theory behind active low-pass, high-pass and band-pass filters?

An RC network followed by a non-inverting amplifier gives a first-order active filter with cut-off fc = 1/(2πRC) and pass-band gain Af = 1 + Rf/R1. Unlike a passive filter, it can have gain and drives a load without changing its response. A band-pass filter can be made by cascading a high-pass and a low-pass section with fL < fH.

What result should I get in active low-pass, high-pass and band-pass filters?

fc = ___ Hz (design 1 kHz), pass-band gain = ___ dB, roll-off ≈ 20 dB/decade.

What precautions should I take in active low-pass, high-pass and band-pass filters?

Keep the input amplitude constant and below clipping. Use the nearest standard resistor and note the change in fc.

Active low-pass, high-pass and band-pass filters