To build an op-amp integrator and differentiator and observe their outputs for square and sine inputs.
- IC 741
- Resistors 10 kΩ, 100 kΩ, 1 kΩ
- Capacitors 0.01 µF, 0.1 µF
- Dual supply ±12 V
- Function generator
- CRO
Theory
Integrator: Vo = −(1/RC)∫Vin dt, so a square input gives a triangle. A resistor Rf across C (about 10R) stops the output drifting to saturation. Differentiator: Vo = −RC·dVin/dt, so a triangle gives a square and a square gives spikes. A small series resistor at the input limits high-frequency gain. For a ±Vp square at frequency f the integrator's output swing is Vp / (2fRC) peak-to-peak.
- Integrator: input → R → pin 2; C from pin 2 to 6, with Rf in parallel; pin 3 to ground
- Differentiator: input → C (with small series R) → pin 2; R from pin 2 to 6; pin 3 to ground
Procedure
Pre-lab check
4 questions · 75% to be readyTry the readings before the lab
| f (Hz) | Integrator out p-p, square in (V) | Differentiator out peak, sine in (V) |
|---|---|---|
| 100 | 5 | 0.628 |
| 200 | 2.5 | 1.257 |
| 500 | 1 | 3.142 |
| 1000 | 0.5 | 6.283 |
| 2000 | 0.25 | 10.5 |
| 5000 | 0.1 | 10.5 |
Precautions
- Keep Rf across the integrator capacitor to avoid saturation.
- Use a low input frequency so the output does not clip.
My readings
Type what you measured. It goes into your record book, and to My Garage when you are signed in.
| S. No. | f (Hz) | Integrator out p-p, square in (V) | Differentiator out peak, sine in (V) |
|---|---|---|---|
| 1 | |||
| 2 | |||
| 3 | |||
| 4 | |||
| 5 | |||
| 6 |
Check my readings
Put the value you set in the first column, then compare. Real parts have tolerance.
Square in gives a triangle out of ___ V p-p from the integrator (theory ___). The differentiator turns a sine into a cosine of amplitude ___ V.
Everything above is free. The print-ready write-up comes with Maker.
Printed pages leave the observation table empty for your own readings.
Viva questions
Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.
Quick answers for your record and viva
What is the aim of the op-amp integrator and differentiator experiment?
To build an op-amp integrator and differentiator and observe their outputs for square and sine inputs.
What apparatus is needed for op-amp integrator and differentiator?
IC 741, Resistors 10 kΩ, 100 kΩ, 1 kΩ, Capacitors 0.01 µF, 0.1 µF, Dual supply ±12 V, Function generator, CRO.
What is the theory behind op-amp integrator and differentiator?
Integrator: Vo = −(1/RC)∫Vin dt, so a square input gives a triangle. A resistor Rf across C (about 10R) stops the output drifting to saturation. Differentiator: Vo = −RC·dVin/dt, so a triangle gives a square and a square gives spikes. A small series resistor at the input limits high-frequency gain. For a ±Vp square at frequency f the integrator's output swing is Vp / (2fRC) peak-to-peak.
What result should I get in op-amp integrator and differentiator?
Square in gives a triangle out of ___ V p-p from the integrator (theory ___). The differentiator turns a sine into a cosine of amplitude ___ V.
What precautions should I take in op-amp integrator and differentiator?
Keep Rf across the integrator capacitor to avoid saturation. Use a low input frequency so the output does not clip.
