Touch-free sanitiser and temperature kiosk
Schools, offices and clinics still check temperature and give sanitiser at the entrance, often by a guard with a handheld gun. A kiosk that does both touch-free and counts visitors frees that person for other work.
- Parts
- ₹2,555
- Build
- 7 weeks
- Board
- Arduino Uno
- Objectives
- 5
Block diagram
- IR hand sensorDetects a hand under the nozzle
- MLX90614Measures forehead or wrist temperature
- Arduino UnoRuns the kiosk
- PumpDispenses sanitiser
- LCD and buzzerShow temperature, warn on fever
- Voice moduleSpeaks alerts from recorded clips+
Objectives
- To dispense a measured dose (about 1 mL) when a hand is detected.
- To measure temperature at a fixed distance and correct it for skin.
- To warn on fever above 37.5 °C.
- To count visitors and dispenses each day.
- To announce readings and alerts by voice in two languages.
Parts and specifications
- Arduino Uno R3 (CH340 clone)ATmega328P 16 MHz, 32 KB flash, 2 KB SRAM, 5 V logic, 6 analog inputs (10-bit), 6 PWM pins₹450Buy
- IR obstacle sensor moduleReflective IR pair with LM393, 2 to 30 cm set by trimmer, digital out, sunlight can false-trigger₹80Buy
- MLX90614 IR thermometerNon-contact, 0.02 °C resolution, ±0.5 °C near body temperature, 90° field of view, I²C₹900Buy
- IRLZ44N logic-level MOSFET55 V 47 A, fully on at VGS 4.5 V (RDS(on) about 25 mΩ), good from 5 V pins₹40Buy
- 16×2 LCD with I²C backpackHD44780, PCF8574 at 0x27 or 0x3F, 5 V, contrast trimmer on the back₹220Buy
- Bottle, tube, nozzle and stand₹250
- 5 V 2 A adapter₹150
- 4 GB microSD card₹200
Total about ₹2,555 at typical online prices. Tap a part for its pinout and datasheet notes.
Design calculations
Pump 1.4 L/min = 23 mL/s. A 1 mL dose needs about 45 ms; tune by weighing 20 doses on a kitchen scale.
The MLX90614 has a 90° field of view: at 5 cm it sees a 10 cm circle, about a forehead. Farther away it averages in the background, so only read when the forehead sensor confirms the person is close.
Forehead skin reads 1 to 2 °C below core. Add an offset measured against a clinical thermometer on 20 people.
Pin map
| Signal | Pin or connection |
|---|---|
| Hand IR sensor | D2 |
| Forehead IR sensor (distance check) | D3 |
| MLX90614 SDA / SCL | A4 / A5 (0x5A) |
| Pump MOSFET gate | D5 (via 100 Ω, 10 kΩ pull-down, diode across pump) |
| LCD / buzzer | A4, A5 shared / D8 |
Firmware outline
- Hand detected → pump on for the dose time, then lock out for 2 s.
- Forehead detected → wait 300 ms, average 5 readings, add the offset.
- Show temperature; above 37.5 °C beep three times and show 'Please see staff'.
- Count visitors and doses in EEPROM; show totals in admin mode.
Test plan
| Test | Expected result |
|---|---|
| 20 doses weighed | Mean dose and spread |
| Hand held under nozzle | Only one dose |
| Temperature vs clinical thermometer on 20 people | Within ±0.5 °C |
| Warm water bottle at 39 °C | Fever warning |
These rows start your results table when you plan the project.
Viva practice
Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 5.
Make it yours
One or two upgrades for a mini project, two to four for a major one.
Build these first
Datasheets and sources to cite
- Melexis MLX90614 datasheet
- ISO 80601-2-56 (clinical thermometers)
- WHO hand hygiene guidance
About this project
How much does the touch-free sanitiser and temperature kiosk project cost?
About ₹2,195 for the parts in the base list: Arduino Uno R3 (CH340 clone), IR obstacle sensor module × 2, MLX90614 IR thermometer, Mini submersible pump 3 to 6 V, IRLZ44N logic-level MOSFET, 16×2 LCD with I²C backpack, Active buzzer 5 V, Bottle, tube, nozzle and stand, 5 V 2 A adapter.
How long does it take?
About 6 weeks for the base project, built on an Arduino Uno. Each upgrade adds time.
Which branches is it suitable for?
Electronics and Communication, Instrumentation, Biomedical, Diploma (any electronics branch), as a mini project.
Which pins and design calculations does it use?
Hand IR sensor on D2; Forehead IR sensor (distance check) on D3; MLX90614 SDA / SCL on A4 / A5 (0x5A). Worked calculations on this page: dose, measuring distance, skin offset.
How do I test it?
20 doses weighed: Mean dose and spread. Hand held under nozzle: Only one dose. Temperature vs clinical thermometer on 20 people: Within ±0.5 °C. Warm water bottle at 39 °C: Fever warning.
What are the objectives?
To dispense a measured dose (about 1 mL) when a hand is detected. To measure temperature at a fixed distance and correct it for skin. To warn on fever above 37.5 °C. To count visitors and dispenses each day.
