Tools / Series RLC resonance and impedance
How to work out series RLC resonance, Q and impedance
The inductor and capacitor swap energy at one frequency. The resistor decides how sharp that peak is.
f0 = 1 ÷ 2π√(LC); Q = (1 ÷ R)√(L ÷ C); Z = R + j(ωL − 1 ÷ ωC)
Result
- Resonant frequency
- 5.033 kHz
- Q factor
- 31.62
- Bandwidth
- 159.2 Hz
- Reactance at resonance
- 316.2 Ω
- Impedance at test frequency
- 10.83 Ω
- Phase at test frequency (°)
- -22.54
- Behaviour
- Under-damped: rings after a step
Step by step
The working with your numbers
- Units: henries and farads
L = 0.01 H, C = 10⁻⁷ F - Resonant frequency
f0 = 1 ÷ (2π√(LC)) = 1 ÷ (2π × 3.16 × 10⁻⁵) = 5.03 kHzAt f0 the inductor's and capacitor's reactances are equal and cancel. - Reactance of each at f0
X = 2πf0L = 316 Ω - Quality factor
Q = X ÷ R = 316 ÷ 10 = 31.6Q is the same as (1 ÷ R) × √(L ÷ C). - Bandwidth between the −3 dB points
BW = f0 ÷ Q = 159 Hz - Impedance at 5 kHz
XL = 314 Ω, XC = 318 Ω, |Z| = √(R² + (XL − XC)²) = 10.8 Ω - Phase there
φ = arctan((XL − XC) ÷ R) = −22.5°Positive means inductive (current lags), negative means capacitive (current leads).
Does the answer make sense?
- OK: At resonance the impedance falls to R = 10 Ω and the phase is 0°. That is the minimum, so the current is at its largest.
- OK: With Q = 31.6, the voltage across the L or C alone reaches 31.6 times the source voltage at f0. Check their voltage ratings.
- OK: Real inductors add winding resistance and capacitors add ESR. Add them to R, or the measured peak will be lower than 31.6. Reactance at f0 is 316 Ω.
Pick a real part
- Standard parts: L = 10 mH, C = 100 nF give f0 = 5.03 kHz. Capacitors of ±10 % and inductors of ±10 % to ±20 % move f0 by about ±7 % to ±15 %.
- Measure f0 on the bench as the frequency where Vout across R is highest, or where the phase between source and current is zero.
Common mistakes
- Leaving out the coil's own resistance. It sets the real Q.
- Expecting the source voltage to appear across the resistor only. At resonance L and C each carry Q times the source voltage.
- Mixing up series and parallel resonance. In a parallel tank the impedance is a maximum at f0, not a minimum.
Learn it, try it, build it
Calculated, not measured. Check the exact part datasheet and your real circuit before powering anything.
Common questions
How do you work out the resonant frequency of an RLC circuit?
f0 = 1 ÷ (2π√(LC)). With 10 mH and 100 nF: √(1×10⁻⁹) = 31.6 µs, so f0 = 1 ÷ (2π × 31.6 µs) ≈ 5.03 kHz.
What does the Q factor of a series RLC circuit mean?
Q = (1 ÷ R)√(L ÷ C). A higher Q means a sharper peak and a narrower bandwidth, BW = f0 ÷ Q. At resonance L and C each carry Q times the source voltage.
