Wi-Fi LED strip controller with WLED
Build it step by step
0 of 8 doneFlash WLED
Use the web installer over USB.
Connect to the setup network
Join the access point WLED creates and enter your home Wi-Fi.
Wire the strip
Wire the level shifter, 330 Ω resistor and capacitor.
Set the LED count
In LED preferences set the number of LEDs and GPIO 16.
Set the power limit
Set the maximum current to 3 A and check the supply stays cool.
Play with effects
Pick effects and colours from the phone app.
Add a preset
Save a favourite and a sunset schedule in the timers.
Fit it in a box
Mount the ESP32 and level shifter in a ventilated box.
How do you build a wi-Fi LED strip controller with WLED?
An ESP32 running WLED controls an addressable strip from a phone app with effects, schedules and music sync. You need ESP32 DevKit V1, WS2812B strip 5 m (30 LEDs/m), 74HCT245 level shifter (for WS2812), 5 V 2 A USB adapter, Resistor 330 Ω, Electrolytic capacitor 1000 µF and ABS project box (100 × 60 × 25 mm). It takes 8 steps and about 60 minutes.
- Level
- Beginner
- Time
- About 60 min
- Parts
- 7
Parts list
- Development BoardsBuyESP32 DevKit V1 × 1
- OptoelectronicsBuy
- Integrated Circuits
- PowerBuy
- PassivesBuyResistor 330 Ω × 1
- PassivesBuy
- Mechanical & HardwareBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 5 V supply + | Strip + and the 1000 µF capacitor + | Strip power |
| 5 V supply - | Strip - and capacitor - and ESP32 GND | Common ground |
| 5 V supply + | ESP32 VIN | Power the ESP32 from the same supply |
| ESP32 GPIO16 | 74HCT245 pin 2 (A1) | Data from the ESP32 |
| 74HCT245 pin 18 (B1) | 330 Ω resistor then strip DIN | Level-shifted data |
| 74HCT245 pin 20 (VCC) | 5 V supply + | Power |
| 74HCT245 pin 10 (GND) | Ground | Ground |
| 74HCT245 pin 1 (DIR) | 5 V | Direction A to B |
| 74HCT245 pin 19 (OE) | Ground | Outputs enabled |
| 74HCT245 pins 3 to 9 (A2 to A8) | Ground | Unused inputs tied low |
No code needed
No code to write: WLED is open-source firmware that you flash from a browser. Open the WLED web installer in Chrome or Edge with the ESP32 connected by USB and follow the steps. The 74HCT245 turns the 3.3 V data signal into a clean 5 V one, which makes the strip more reliable. Power is the main risk: a full metre of white pixels can draw about 1.8 A, so five metres (150 LEDs) can draw over 9 A at full brightness. Use only a section of the strip (about 60 LEDs, 2 m) on a 5 V 4 A supply, and set a maximum current of 3 A in WLED under LED preferences, which dims the strip automatically to stay within it. Fit the 1000 µF capacitor close to the strip, keep the supply wires short and thick, and never leave a strip on a power supply that gets hot. The default setup access point and password are public, so change the password when you set up your network and do not share your Wi-Fi details.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Power up | WLED access point appears |
| LED count set | Whole strip lights correctly |
| Power limit active | Strip dims at full white instead of overheating |
| Schedule | Lights change at the set time |
If it does not work
Wrong colours
Change the colour order in LED preferences.
First LED flickers
Check the level shifter and the 330 Ω resistor.
Strip resets when bright
Lower the current limit or use a stronger supply.
Cannot find it on Wi-Fi
Check the 2.4 GHz network and the credentials.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the wi-Fi LED strip controller with WLED?
ESP32 DevKit V1, WS2812B strip 5 m (30 LEDs/m), 74HCT245 level shifter (for WS2812), 5 V 2 A USB adapter, Resistor 330 Ω, Electrolytic capacitor 1000 µF and ABS project box (100 × 60 × 25 mm).
How long does the wi-Fi LED strip controller with WLED take to build?
About 60 minutes for a beginner maker, in 8 steps.
How do I know the wi-Fi LED strip controller with WLED works?
Power up: WLED access point appears. LED count set: Whole strip lights correctly. Power limit active: Strip dims at full white instead of overheating.
Wrong colours: what should I check?
Change the colour order in LED preferences.
First LED flickers: what should I check?
Check the level shifter and the 330 Ω resistor.
Strip resets when bright: what should I check?
Lower the current limit or use a stronger supply.
Cannot find it on Wi-Fi: what should I check?
Check the 2.4 GHz network and the credentials.
