Projects / Wire gauge voltage drop lab

Wire gauge voltage drop lab

Beginner50 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. SILICOHOOK

    Cut the wires

    One metre of 22 AWG and one metre of 18 AWG, ends stripped.

  2. Measure the supply

    Note the pack voltage with no load.

  3. SILICOHOOK

    Wire the loop

    Battery plus, the 22 AWG wire, the resistor, battery minus.

  4. Switch on for ten seconds

    Read the voltage across the resistor, to find the current as volts divided by 10.

  5. SILICOHOOK

    Measure across the wire

    Probes on the two ends of the wire, read the millivolts.

  6. SILICOHOOK

    Repeat with the 18 AWG wire

    Note that the drop is smaller.

  7. SILICO

    Work out the resistance

    Divide the drop in volts by the current, and compare with 0.053 and 0.021 ohm per metre.

In short

How do you build a wire gauge voltage drop lab?

Send a few hundred milliamps through a metre each of thin and thick wire to a power resistor and measure the small voltage lost along each, so you can see why thin wire is poor for heavy loads and choose a wire size. You need Silicone wire 18 AWG (red and black), Hook-up wire 22 AWG solid (6 colours), Power resistor 10 Ω 5 W (cement), Battery holder 4 × AA with switch, AA alkaline battery × 4 and Digital multimeter. It takes 7 steps and about 50 minutes.

Level
Beginner
Time
About 50 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Battery holder plusOne end of the test wireSupply to the wire
Other end of the test wirePower resistor lead 1The wire carries the load current
Power resistor lead 2Battery holder minusCompletes the loop
Meter probesAcross the two ends of the test wireMeasures the voltage lost in the wire
Meter dialThe lowest DC volts range, 200 mV if you have oneSmall drops need a sensitive range

No code needed

No code. With 6 V across a 10 ohm resistor the current is about 0.6 A. Each metre of 22 AWG wire has a resistance of about 0.053 ohm, so it should lose about 32 mV, while a metre of 18 AWG has about 0.021 ohm and should lose about 13 mV. The wire loses voltage equal to the current times its resistance, so doubling the length doubles the loss, and a thicker wire loses less. This matters most for low-voltage runs, such as a long cable to LED strip. Safety: the resistor takes about 3.6 W, so it gets hot on its 5 W rating. Put it on a ceramic tile or a heatproof mat away from anything that burns, switch the circuit on only for ten to twenty seconds at a time, and do not touch the resistor until it has cooled. Use only the 6 V pack and nothing higher.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Pack with no loadAbout 6.2 to 6.5 V with fresh cells
Resistor voltage under loadAbout 5.8 to 6.2 V, so about 0.6 A
22 AWG metre dropAbout 30 mV
18 AWG metre dropAbout 12 mV
Two metres of 22 AWGAbout twice the drop of one metre

If it does not work

Drop reads much larger

A bad contact, so twist and clamp the joints firmly.

Drop reads zero

The meter is on the wrong range, or the probes are across the resistor.

Resistor too hot

Shorten the test or let it cool between readings.

Pack voltage sags

The cells are tired, so use fresh ones.

Readings drift

Wire and resistor warm up, so read quickly.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the wire gauge voltage drop lab?

Silicone wire 18 AWG (red and black), Hook-up wire 22 AWG solid (6 colours), Power resistor 10 Ω 5 W (cement), Battery holder 4 × AA with switch, AA alkaline battery × 4 and Digital multimeter.

How long does the wire gauge voltage drop lab take to build?

About 50 minutes for a beginner maker, in 7 steps.

How do I know the wire gauge voltage drop lab works?

Pack with no load: About 6.2 to 6.5 V with fresh cells. Resistor voltage under load: About 5.8 to 6.2 V, so about 0.6 A. 22 AWG metre drop: About 30 mV.

Drop reads much larger: what should I check?

A bad contact, so twist and clamp the joints firmly.

Drop reads zero: what should I check?

The meter is on the wrong range, or the probes are across the resistor.

Resistor too hot: what should I check?

Shorten the test or let it cool between readings.

Pack voltage sags: what should I check?

The cells are tired, so use fresh ones.