Projects / Push-pull force gauge

Push-pull force gauge

Intermediate2 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANO++264 g

    Mount the load cell

    Fix one end to a base and put the handle on the free end, with spacers so the cell can flex.

  2. NANO+265 g

    Wire the amplifier

    Connect the four wires to the HX711 and the HX711 to the Nano.

  3. NANO

    Read raw values

    With the sketch at factor 1 you will see raw counts. Check they change when you push.

  4. NANO

    Calibrate

    Hang a known mass, send c and its mass in kg, for example c2.0, in the Serial Monitor.

  5. NANO

    Test both directions

    Push down and pull up. Swap the signal wires if pulling shows positive.

  6. NANO

    Use peak hold

    Press the button to clear the peak and tare.

In short

How do you build a push-pull force gauge?

A load cell on a handle measures pushing and pulling force in newtons, with a peak-hold function. You need Arduino Nano, Load cell 20 kg, HX711 load cell amplifier, SSD1306 OLED Display and Tactile push button 6 mm. It takes 6 steps and about 120 minutes.

Level
Intermediate
Time
About 120 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Load cell red (E+)HX711 E+Excitation
Load cell black (E-)HX711 E-Excitation
Load cell white (A-)HX711 A-Signal (swap with green if the sign is backwards)
Load cell green (A+)HX711 A+Signal
HX711 DTNano D3Data
HX711 SCKNano D2Clock
HX711 VCC, GNDNano 5V, GNDPower
OLED SDA, SCLNano A4, A5I2C
OLED VCC, GNDNano 5V, GNDPower
ButtonNano D4 and GNDResets the peak hold

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install "HX711" by bogde and "U8g2". Mount the 20 kg bar-type cell with one end fixed and the other end carrying the handle; the arrow on the cell shows the loading direction. Never load it past 20 kg, which is about 196 N, and treat the figures as indicative unless calibrated against a known weight.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <HX711.h>
#include <EEPROM.h>
#include <U8x8lib.h>

HX711 scale;
U8X8_SSD1306_128X64_NONAME_HW_I2C oled(U8X8_PIN_NONE);
const byte BTN = 4;
const float G = 9.81;
float calFactor = 1.0;      // HX711 counts per kg; set with the c command
float peak = 0;

void setup() {
  Serial.begin(115200);
  pinMode(BTN, INPUT_PULLUP);
  scale.begin(3, 2);
  EEPROM.get(0, calFactor);
  if (isnan(calFactor) || calFactor == 0) calFactor = 1.0;
  scale.set_scale(calFactor);
  scale.tare();
  oled.begin();
  oled.setFont(u8x8_font_chroma48medium8_r);
}

void loop() {
  if (Serial.available()) {                      // calibrate: hang a known weight, send c and its mass in kg, for example c2.0
    if (Serial.read() == 'c') {
      float kg = Serial.parseFloat();
      scale.set_scale();                         // raw counts
      calFactor = scale.get_units(10) / kg;
      scale.set_scale(calFactor);
      EEPROM.put(0, calFactor);
      Serial.print("Factor "); Serial.println(calFactor);
    }
  }
  if (digitalRead(BTN) == LOW) { peak = 0; scale.tare(); delay(300); }
  float newtons = scale.get_units(3) * G;
  if (fabs(newtons) > fabs(peak)) peak = newtons;
  char b[17], v[8];
  dtostrf(newtons, 6, 1, v); snprintf(b, sizeof b, "Now %s N", v); oled.drawString(0, 2, b);
  dtostrf(peak, 6, 1, v);    snprintf(b, sizeof b, "Max %s N", v); oled.drawString(0, 4, b);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
No loadAbout 0.0 N
Known 2 kg massReads about 19.6 N
PullingReads negative
ReleaseMax keeps the largest push or pull until the button is pressed

If it does not work

Readings drift

Let the HX711 warm up and avoid touching the cell during tare.

Sign backwards

Swap the white and green wires.

Noisy readings

Use shorter wires and average more samples.

Not accurate

Calibrate again with a mass near what you will measure.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the push-pull force gauge?

Arduino Nano, Load cell 20 kg, HX711 load cell amplifier, SSD1306 OLED Display and Tactile push button 6 mm.

How long does the push-pull force gauge take to build?

About 120 minutes for a intermediate maker, in 6 steps.

How do I know the push-pull force gauge works?

No load: About 0.0 N. Known 2 kg mass: Reads about 19.6 N. Pulling: Reads negative.

Readings drift: what should I check?

Let the HX711 warm up and avoid touching the cell during tare.

Sign backwards: what should I check?

Swap the white and green wires.

Noisy readings: what should I check?

Use shorter wires and average more samples.

Not accurate: what should I check?

Calibrate again with a mass near what you will measure.