Build it step by step
0 of 7 donePlan the pins
Write down the pin list and the LED order before wiring.
Set the reference
REF OUT to RHI and to ground through two 1 kΩ in series. RLO and REF ADJ to ground.
Add the LEDs
Anodes to +12 V, cathodes to pins 1, 18, 17 and the rest in order, green to red.
Add the input stage
Jack tip to the pot, pot wiper to the 1N4148, and then to node X with 10 µF and 10 kΩ to ground.
Connect SIG
Node X to pin 5.
Test with music
Play music from a phone into the jack. The lit LEDs follow the volume.
Pick a mode
Leave pin 9 open for dot mode or tie it to V+ for bar mode.
How do you build an LED VU meter with LM3914?
An LM3914 lights a bar of ten LEDs to show the level of a music signal, no microcontroller needed. You need LM3914 bar graph driver, LED 5 mm red × 3, LED 5 mm yellow × 3, LED 5 mm green × 4, Signal Diode 1N4148, Electrolytic capacitor 10 µF, Resistor 1 kΩ × 2, Resistor 10 kΩ, Potentiometer 10 kΩ, Audio jack 3.5 mm (PCB, stereo), Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and 12 V 2 A DC adapter. It takes 7 steps and about 60 minutes.
- Level
- Beginner
- Time
- About 60 min
- Parts
- 13
Parts list
- Integrated CircuitsBuy
- SemiconductorsBuyLED 5 mm red × 3
- SemiconductorsBuyLED 5 mm yellow × 3
- SemiconductorsBuyLED 5 mm green × 4
- SemiconductorsBuy
- PassivesBuy
- PassivesBuyResistor 1 kΩ × 2
- PassivesBuyResistor 10 kΩ × 1
- PassivesBuy
- ConnectorsBuy
- PrototypingBuy
- PrototypingBuy
- PowerBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 12 V adapter + | LM3914 pin 3 (V+), and every LED anode | Supply |
| 12 V adapter - | LM3914 pin 2 (V-), pin 4 (RLO) and pin 8 (REF ADJ) | Ground |
| Pin 7 (REF OUT) | Pin 6 (RHI), and two 1 kΩ in series to GND | Reference 1.25 V, LED current about 6 mA |
| LED cathodes (green first) | Pins 1, 18, 17, 16 (green), 15, 14, 13 (yellow), 12, 11, 10 (red) | Ten LEDs in order |
| Audio jack tip | Pot top; pot bottom and jack sleeve to GND | Sensitivity control |
| Pot wiper | 1N4148 anode | Rectifier |
| 1N4148 cathode | Node X with 10 µF to GND and 10 kΩ to GND | Peak detector with a decay of about 0.1 s |
| Node X | Pin 5 (SIG) | Signal input |
| Pin 9 (MODE) | Open for dot mode, to V+ for bar mode | Display style |
No code needed
No code. LM3914 pins: 1 is LED 1, 2 is V−, 3 is V+, 4 is RLO, 5 is SIG, 6 is RHI, 7 is REF OUT, 8 is REF ADJ, 9 is MODE, and pins 10 to 18 are LED 10 down to LED 2. In bar mode with a 12 V supply the chip can run warm, so start in dot mode and consider a lower supply for long use.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Silence | No LEDs lit, or just the first |
| Loud music | Top LEDs flash with the beat |
| Turn the pot down | Fewer LEDs light |
| Bar mode | All LEDs up to the level are on |
If it does not work
All LEDs lit
Reference or RLO wiring is wrong. Check pins 4, 6, 7 and 8.
No LEDs ever
The signal is too small. Turn the pot up or use the phone at a higher volume.
LEDs flicker too fast
The peak detector decays quickly. Use a larger capacitor.
Chip too hot
Use dot mode, a lower supply or a bigger R_ref.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the LED VU meter with LM3914?
LM3914 bar graph driver, LED 5 mm red × 3, LED 5 mm yellow × 3, LED 5 mm green × 4, Signal Diode 1N4148, Electrolytic capacitor 10 µF, Resistor 1 kΩ × 2, Resistor 10 kΩ, Potentiometer 10 kΩ, Audio jack 3.5 mm (PCB, stereo), Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and 12 V 2 A DC adapter.
How long does the LED VU meter with LM3914 take to build?
About 60 minutes for a beginner maker, in 7 steps.
How do I know the LED VU meter with LM3914 works?
Silence: No LEDs lit, or just the first. Loud music: Top LEDs flash with the beat. Turn the pot down: Fewer LEDs light.
All LEDs lit: what should I check?
Reference or RLO wiring is wrong. Check pins 4, 6, 7 and 8.
No LEDs ever: what should I check?
The signal is too small. Turn the pot up or use the phone at a higher volume.
LEDs flicker too fast: what should I check?
The peak detector decays quickly. Use a larger capacitor.
Chip too hot: what should I check?
Use dot mode, a lower supply or a bigger R_ref.
