Transistor fuzz guitar pedal
Build it step by step
0 of 7 doneBuild the first stage
Bias the collector to half supply.
Add the second stage
Coupled by a capacitor.
Add the controls
Fuzz and volume pots.
Wire the footswitch
True bypass.
Test with a guitar
Try different settings.
Look at the wave
See the clipping on a scope.
Box it
Metal box and jacks.
How do you build a transistor fuzz guitar pedal?
A two-transistor fuzz circuit in a metal box with a footswitch, input and output jacks and a 9 V battery. You need BC547 NPN transistor × 2, Resistor 1 kΩ × 2, Resistor 100 kΩ, Resistor 470 kΩ, Resistor 10 kΩ, Potentiometer 10 kΩ × 2, Electrolytic capacitor 1 µF × 2, Electrolytic capacitor 10 µF, LED 5 mm red, Foot switch (momentary), Audio jack 3.5 mm (PCB, stereo) × 2, 9 V battery, 9 V battery snap with DC jack and ABS project box (100 × 60 × 25 mm). It takes 7 steps and about 180 minutes.
- Level
- Intermediate
- Time
- About 180 min
- Parts
- 14
Parts list
- SemiconductorsBuy
- PassivesBuyResistor 1 kΩ × 2
- PassivesBuyResistor 100 kΩ × 1
- PassivesBuyResistor 470 kΩ × 1
- PassivesBuyResistor 10 kΩ × 1
- PassivesBuy
- PassivesBuy
- PassivesBuy
- SemiconductorsBuyLED 5 mm red × 1
- SwitchesBuyUse a latching 3PDT footswitch for true bypass
- ConnectorsBuyUse 6.35 mm jacks for guitar cables
- BatteriesBuy9 V battery × 1
- PowerBuy
- Mechanical & HardwareBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Input jack | 1 µF capacitor to the first base | Guitar input |
| First collector | Second base through 10 µF | Stage coupling |
| 470 kΩ and 100 kΩ resistors | Bias the first stage | Bias |
| Fuzz pot | Between the emitter and ground | Gain control |
| Volume pot | Output | Level |
| 9 V battery | Footswitch, then supply rail | Power |
| LED with 10 kΩ | Across the supply | On indicator |
No code needed
Two transistors in cascade give a lot of gain, and when the signal grows beyond what the supply can hold it flattens at the top and bottom; this is clipping, the harsh sound called fuzz. Set the bias so the first collector sits near half supply; if it sits too close to the rail you get gated, sputtery fuzz. The fuzz pot changes the gain, and the volume pot sets the output level, which matters because fuzz is loud. A footswitch bypass lets the guitar go straight through when the pedal is off. Look at the clipped wave on an oscilloscope or an audio app. Use a 9 V battery only, not a mains adapter with an unknown polarity, and unplug the input jack when not playing to save the battery.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Footswitch off | Clean guitar passes straight through |
| Footswitch on | Fuzzy tone |
| Fuzz pot | Changes the amount of clipping |
| Volume pot | Matches the clean level |
If it does not work
No sound
Check jack wiring and bias.
Sputtery fuzz
Re-tune the first stage bias.
Hum
Use a metal box with a grounded jack.
Battery drains
Unplug the input jack when you stop.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the transistor fuzz guitar pedal?
BC547 NPN transistor × 2, Resistor 1 kΩ × 2, Resistor 100 kΩ, Resistor 470 kΩ, Resistor 10 kΩ, Potentiometer 10 kΩ × 2, Electrolytic capacitor 1 µF × 2, Electrolytic capacitor 10 µF, LED 5 mm red, Foot switch (momentary), Audio jack 3.5 mm (PCB, stereo) × 2, 9 V battery, 9 V battery snap with DC jack and ABS project box (100 × 60 × 25 mm). Foot switch (momentary): Use a latching 3PDT footswitch for true bypass. Audio jack 3.5 mm (PCB, stereo) × 2: Use 6.35 mm jacks for guitar cables.
How long does the transistor fuzz guitar pedal take to build?
About 180 minutes for a intermediate maker, in 7 steps.
How do I know the transistor fuzz guitar pedal works?
Footswitch off: Clean guitar passes straight through. Footswitch on: Fuzzy tone. Fuzz pot: Changes the amount of clipping.
No sound: what should I check?
Check jack wiring and bias.
Sputtery fuzz: what should I check?
Re-tune the first stage bias.
Hum: what should I check?
Use a metal box with a grounded jack.
Battery drains: what should I check?
Unplug the input jack when you stop.
