Projects / Zener and transistor regulator

Zener and transistor regulator

Beginner1 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. Check the zener alone

    Wire the 1 kΩ and zener from 12 V and measure the zener voltage with the meter.

  2. TIP31C

    Add the transistor

    Wire the collector to 12 V, the base to the zener node and read the emitter voltage.

  3. Fit the capacitors

    Add the 100 µF capacitors on the input and output.

  4. 4.98V

    Add the test load

    Connect the two 220 Ω resistors and see how little the output changes.

  5. Measure regulation

    Note the output with the load off and on, and with the input changed to a 9 V battery.

  6. 4.98V

    Work out the heat

    Calculate (Vin − Vout) × current and decide when a heatsink is needed.

  7. Compare with a 7805

    Measure a 7805 at the same load and compare the line and load regulation.

In short

How do you build a zener and transistor regulator?

A zener diode and a power transistor make a simple regulated supply, to learn what is inside a 7805. You need Zener diode 5.1 V (1N4733A), TIP31C NPN power transistor, Resistor 1 kΩ, Electrolytic Capacitor 100 µF × 2, Resistor 220 Ω × 2, Heatsink TO-220, 12 V 2 A DC adapter, DC barrel to screw terminal adapter (female), Digital multimeter and Breadboard 830 Tie Points. It takes 7 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
10
See the electronics first. This build uses transistor switch. Try a transistor switch in the circuit builder and watch the voltages and currents before you wire it.

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
12 V adapter via DC jack breakout +Breadboard + railInput
12 V adapter via DC jack breakout -Breadboard - railGround
100 µF capacitor (input)Across + rail and - rail, + to the railInput smoothing
+ railTIP31C collectorPass transistor
1 kΩ resistor+ rail and TIP31C baseFeeds the zener and base
Zener 1N4733A cathode (band)TIP31C baseReference
Zener anode- railGround
TIP31C emitterOutput nodeRegulated output
100 µF capacitor (output)Output node and - rail, + to the outputOutput smoothing
Two 220 Ω resistors in parallelOutput node and - railTest load of about 40 mA

No code needed

No code. TIP31C pins, flat face towards you and legs down, are base, collector, emitter from the left. The emitter sits one base-emitter drop (about 0.7 V) below the zener voltage, so expect about 4.4 V out rather than 5 V. With a 1 kΩ resistor the circuit supports a load of roughly 100 mA before the zener loses its bias; for more current use a smaller resistor and a heatsink. The transistor dissipates (12 V − 4.4 V) × load current, for example 0.76 W at 100 mA.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
No loadAbout 4.4 V out
40 mA loadWithin about 0.1 V of the no-load value
Input swapped for a 9 V batteryOutput stays within about 0.2 V
100 mA loadOutput starts to sag and the transistor gets warm

If it does not work

Output about 0.6 V

The zener is the wrong way round. Cathode (band) goes to the base.

Output equals the input

Base resistor and zener are not connected to the same node.

Transistor very hot

Load is too high. Reduce it or fit the heatsink.

Output drops sharply under load

The base current is starving the zener. Use a smaller resistor.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the zener and transistor regulator?

Zener diode 5.1 V (1N4733A), TIP31C NPN power transistor, Resistor 1 kΩ, Electrolytic Capacitor 100 µF × 2, Resistor 220 Ω × 2, Heatsink TO-220, 12 V 2 A DC adapter, DC barrel to screw terminal adapter (female), Digital multimeter and Breadboard 830 Tie Points.

How long does the zener and transistor regulator take to build?

About 60 minutes for a beginner maker, in 7 steps.

How do I know the zener and transistor regulator works?

No load: About 4.4 V out. 40 mA load: Within about 0.1 V of the no-load value. Input swapped for a 9 V battery: Output stays within about 0.2 V.

Output about 0.6 V: what should I check?

The zener is the wrong way round. Cathode (band) goes to the base.

Output equals the input: what should I check?

Base resistor and zener are not connected to the same node.

Transistor very hot: what should I check?

Load is too high. Reduce it or fit the heatsink.

Output drops sharply under load: what should I check?

The base current is starving the zener. Use a smaller resistor.