Projects / Meeting room status light

Meeting room status light

Beginner2 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. ESP3213.0 mA

    Wire the matrix

    Add the capacitor first, then the resistor in the data line.

  2. ESP32

    Test the colours

    Temporarily set target values and check red, amber and green.

  3. ESP32

    Set up the status page

    Create a page that returns free, busy or soon, and put its address in STATUS_URL.

  4. ESP32

    Test the fade

    Change the page text and watch the colour fade over about a second.

  5. ESP32

    Set the dim hours

    Adjust the night hours in the code to suit your office.

  6. ESP32USB

    Mount

    Fix the panel at eye level outside the room with the cable and adapter hidden.

In short

How do you build a meeting room status light?

A glowing panel outside a meeting room shows free, busy or starting soon, read from a small status page you control. You need ESP32-C3 SuperMini, WS2812B 8x8 RGB LED matrix, 5 V 2 A USB adapter, Resistor 330 Ω and Electrolytic capacitor 1000 µF. It takes 6 steps and about 120 minutes.

Level
Beginner
Time
About 120 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
5 V USB adapter +Matrix 5V and capacitor +Power
5 V USB adapter -Matrix GND, capacitor - and ESP32-C3 GNDCommon ground
1000 µF capacitorAcross the matrix 5V and GNDSmooths power
ESP32-C3 GPIO4330 Ω resistor then matrix DINData
ESP32-C3 5V pinSame 5 V as the matrixPowers the board

Code

Arduino IDE with the ESP32 boards package, board "ESP32C3 Dev Module" with USB CDC On Boot enabled. Install "Adafruit NeoPixel". Put your Wi-Fi details and the address of a status page in the placeholders. The status page can be any page that returns the word free, busy or soon, for example one you update from your calendar or a small script. Never put calendar passwords or keys in the sketch. Brightness is kept low so the 64 pixels draw well under the 2 A adapter's limit.

Runs on a virtual ESP32-C3 in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <WiFi.h>
#include <HTTPClient.h>
#include <WiFiClientSecure.h>
#include <Adafruit_NeoPixel.h>
#include <time.h>

const char* WIFI_NAME = "YOUR_WIFI_NAME";
const char* WIFI_PASSWORD = "YOUR_WIFI_PASSWORD";
const char* STATUS_URL = "https://YOUR_STATUS_PAGE";   // returns plain text: free, busy or soon

Adafruit_NeoPixel px(64, 4, NEO_GRB + NEO_KHZ800);
float cur[3] = { 0, 0, 0 }, target[3] = { 0, 0, 0 };
unsigned long lastPoll = 0;

void setTarget(const String& s) {
  if (s.indexOf("busy") >= 0)      { target[0] = 255; target[1] = 0;   target[2] = 0; }
  else if (s.indexOf("soon") >= 0) { target[0] = 255; target[1] = 120; target[2] = 0; }
  else                             { target[0] = 0;   target[1] = 255; target[2] = 0; }
}

void poll() {
  WiFiClientSecure client;
  client.setInsecure();                                // no certificate check: a trade-off for a harmless status
  HTTPClient http;
  if (http.begin(client, STATUS_URL) && http.GET() == 200) setTarget(http.getString());
  http.end();
}

void setup() {
  px.begin();
  WiFi.begin(WIFI_NAME, WIFI_PASSWORD);
  while (WiFi.status() != WL_CONNECTED) delay(500);
  configTime(19800, 0, "pool.ntp.org");               // India time, UTC+5:30
}

void loop() {
  if (millis() - lastPoll > 30000 || lastPoll == 0) { poll(); lastPoll = millis(); }
  struct tm t;
  bool night = getLocalTime(&t) && (t.tm_hour < 7 || t.tm_hour >= 19);
  px.setBrightness(night ? 6 : 30);                    // low brightness keeps current under about 0.5 A
  for (int i = 0; i < 3; i++) cur[i] += (target[i] - cur[i]) * 0.05;
  for (int i = 0; i < 64; i++) px.setPixelColor(i, px.Color((uint8_t)cur[0], (uint8_t)cur[1], (uint8_t)cur[2]));
  px.show();
  delay(30);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Page says freeMatrix fades to green
Page says soonAmber
Page says busyRed
After 7 pmPanel is much dimmer

If it does not work

Random colours

Common ground missing or the data resistor is absent.

Nothing lights

Check DIN, not DOUT, is connected and the matrix has 5 V.

No updates

Check the Wi-Fi details and the page address.

Board resets at full brightness

Keep brightness at or below 30 and use a 2 A adapter.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the meeting room status light?

ESP32-C3 SuperMini, WS2812B 8x8 RGB LED matrix, 5 V 2 A USB adapter, Resistor 330 Ω and Electrolytic capacitor 1000 µF.

How long does the meeting room status light take to build?

About 120 minutes for a beginner maker, in 6 steps.

How do I know the meeting room status light works?

Page says free: Matrix fades to green. Page says soon: Amber. Page says busy: Red.

Random colours: what should I check?

Common ground missing or the data resistor is absent.

Nothing lights: what should I check?

Check DIN, not DOUT, is connected and the matrix has 5 V.

No updates: what should I check?

Check the Wi-Fi details and the page address.

Board resets at full brightness: what should I check?

Keep brightness at or below 30 and use a 2 A adapter.