Common-emitter transistor amplifier
Build it step by step
0 of 7 doneSet the bias
Build the divider, transistor and resistors and power on, then measure the collector, which should be near 5 V and the emitter near 0.8 V.
Add the bypass capacitor
Fit the 100 µF across the 1 kΩ emitter resistor.
Couple a signal in
Add the two 10 µF capacitors and the input potentiometer.
Listen or measure
Feed a tone from a phone at low volume and listen to the output with an amplifier or look at it on a scope.
Measure the gain
Gain = output voltage swing ÷ input voltage swing.
Break the bias
Replace the 100 kΩ with 47 kΩ, then 220 kΩ, and see clipping at the top and bottom.
Remove the bypass
Take off the 100 µF and see the gain fall to about 4.7 kΩ ÷ 1 kΩ.
How do you build a common-emitter transistor amplifier?
Bias a BC547 and amplify a small audio signal, measuring gain and seeing distortion when bias is wrong. You need BC547 NPN transistor, Resistor 10 kΩ × 2, Resistor 100 kΩ, Resistor 1 kΩ, Resistor 4.7 kΩ, Electrolytic capacitor 10 µF × 2, Electrolytic Capacitor 100 µF, Potentiometer 10 kΩ, Digital multimeter, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), 9 V battery and 9 V battery snap with DC jack. It takes 7 steps and about 120 minutes.
- Level
- Intermediate
- Time
- About 120 min
- Parts
- 13
Parts list
- SemiconductorsBuy
- PassivesBuyResistor 10 kΩ × 2
- PassivesBuyResistor 100 kΩ × 1
- PassivesBuyResistor 1 kΩ × 1
- PassivesBuyResistor 4.7 kΩ × 1
- PassivesBuy
- PassivesBuy
- PassivesBuy
- Tools & InstrumentsBuy
- PrototypingBuy
- PrototypingBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery + | + rail | Supply |
| 9 V battery - | - rail | Ground |
| 100 kΩ resistor | + rail and BC547 base | Upper bias resistor |
| Two 10 kΩ resistors in series (20 kΩ) | BC547 base and - rail | Lower bias resistor, base sits near 1.5 V |
| 4.7 kΩ resistor | + rail and BC547 collector | Collector load |
| 1 kΩ resistor | BC547 emitter and - rail | Emitter resistor |
| 100 µF capacitor | Across the 1 kΩ, + on the emitter | Bypass for full gain |
| Signal source via 10 kΩ potentiometer | Pot ends to signal and ground, wiper to 10 µF capacitor + | Input level control |
| 10 µF capacitor - | BC547 base | Input coupling |
| 10 µF capacitor + | BC547 collector | Output coupling |
| 10 µF capacitor - | Output | Take the amplified signal here |
No code needed
No code. BC547 flat face towards you with legs down: collector, base, emitter from the left. Design: 9 V, about 0.8 mA collector current; the collector should sit near 5 V (half supply, with room to swing both ways) and the gain is about 4.7 kΩ ÷ the emitter's internal resistance of roughly 32 Ω, so around 100 to 150. A phone's headphone output is far too large at normal volume, so use the potentiometer to set a signal of a few millivolts, and keep the phone volume low.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Power on | Collector about 4 to 6 V, emitter about 0.7 to 1 V |
| Small tone in | Same tone at about 100 times the voltage out |
| Too much input | Output clips flat |
| Bypass capacitor removed | Gain falls to about 4 to 5 |
If it does not work
Collector near 9 V
Transistor is off. Check the base divider and pins.
Collector near 0 V
Transistor is saturated. Check the 100 kΩ resistor value.
Distorted output
Input is too large. Turn the potentiometer down.
No output
Check both coupling capacitors' polarity and positions.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the common-emitter transistor amplifier?
BC547 NPN transistor, Resistor 10 kΩ × 2, Resistor 100 kΩ, Resistor 1 kΩ, Resistor 4.7 kΩ, Electrolytic capacitor 10 µF × 2, Electrolytic Capacitor 100 µF, Potentiometer 10 kΩ, Digital multimeter, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), 9 V battery and 9 V battery snap with DC jack.
How long does the common-emitter transistor amplifier take to build?
About 120 minutes for a intermediate maker, in 7 steps.
How do I know the common-emitter transistor amplifier works?
Power on: Collector about 4 to 6 V, emitter about 0.7 to 1 V. Small tone in: Same tone at about 100 times the voltage out. Too much input: Output clips flat.
Collector near 9 V: what should I check?
Transistor is off. Check the base divider and pins.
Collector near 0 V: what should I check?
Transistor is saturated. Check the 100 kΩ resistor value.
Distorted output: what should I check?
Input is too large. Turn the potentiometer down.
No output: what should I check?
Check both coupling capacitors' polarity and positions.
