Projects / Model tram stop announcer

Model tram stop announcer

Intermediate1.3 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANODFPLAY

    Record the stop names

    And save them as 0001, 0002, 0003 mp3 plus a ding as 0004.

  2. NANO

    Copy them to the SD card

    Formatted as FAT32.

  3. NANO

    Wire the player

    TX to D10, D9 through 1 kilohm to RX, 5V and GND, speaker on SPK1 and SPK2.

  4. NANO

    Wire the two buttons

    D2 and D3, each other leg to GND.

  5. NANO

    Upload the sketch

    It plays the ding and the first stop.

  6. NANO

    Press NEXT and BACK

    It announces the next or previous stop.

  7. NANO

    Check the serial monitor

    It prints the stop name.

In short

How do you build a model tram stop announcer?

A model tram line has three stops, and a button moves to the next one while a recorded voice announces its name through a small speaker. You record the stop names yourself. A good way to try a sound-player module with a Nano. You need Arduino Nano, DFPlayer Mini MP3 module, Speaker 8 Ω 0.5 W, Tactile push button 6 mm × 2, Resistor 1 kΩ, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 80 minutes.

Level
Intermediate
Time
About 80 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
DFPlayer TXNano D10Player to Nano
Nano D91 kilohm resistor to DFPlayer RXNano to player, through a resistor
DFPlayer VCC and GNDNano 5V and GNDPower
DFPlayer SPK1 and SPK2Small 8 ohm speakerThe voice
Next stop buttonNano D2 and GNDMoves forward one stop
Previous stop buttonNano D3 and GNDMoves back one stop

Code

The DFPlayer Mini plays MP3 files from a micro SD card and is controlled by simple serial messages. Format the card as FAT32 and copy on four files named 0001.mp3 to 0004.mp3: the three stop names, which you record yourself with a phone, and a short ding. The Nano talks to the player with a software serial port on D10 and D9, and the D9 line goes through a 1 kilohm resistor because the player's RX pin is happier with a gentler signal. Each button press moves to the next or previous stop, plays the ding, waits a moment and then plays the stop name, and the serial monitor prints the name as well. The player's power wire carries bursts of current, so if you hear clicking or the Nano resets, add a 100 microfarad capacitor across the player's power pins. Install "DFRobotDFPlayerMini" by DFRobot from the Library Manager. Keep the volume moderate for a desk model, and use a small speaker with the player's own amplifier, not a large speaker. Try adding a line map drawn on card with three LEDs that light at the current stop.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Libraries: DFRobotDFPlayerMini.
// Put these files on the FAT32 SD card: 0001.mp3, 0002.mp3 and 0003.mp3 (the three stop names)
// and 0004.mp3 (a short ding).
#include <SoftwareSerial.h>
#include <DFRobotDFPlayerMini.h>

SoftwareSerial dfSerial(10, 9);            // Nano RX = D10, TX = D9
DFRobotDFPlayerMini player;

const uint8_t BTN_NEXT = 2;
const uint8_t BTN_BACK = 3;
const uint8_t STOPS = 3;
const char *NAMES[STOPS] = {"Market Square", "Library", "Station"};   // the words you recorded

uint8_t stopNo = 0;                         // 0 to 2
bool prevNext = false, prevBack = false;

void announce() {
  Serial.print(F("Next stop: "));
  Serial.println(NAMES[stopNo]);
  player.play(4);                           // the ding
  delay(1200);
  player.play(stopNo + 1);                  // the stop name
}

void setup() {
  pinMode(BTN_NEXT, INPUT_PULLUP);
  pinMode(BTN_BACK, INPUT_PULLUP);
  Serial.begin(9600);
  dfSerial.begin(9600);
  delay(1000);
  if (!player.begin(dfSerial)) {
    Serial.println(F("Player not found: check wiring and the SD card."));
    while (true) {}
  }
  player.volume(15);                        // 0 to 30, keep it moderate
  Serial.println(F("Tram ready. Press NEXT or BACK."));
  announce();
}

void loop() {
  bool n = (digitalRead(BTN_NEXT) == LOW);
  bool b = (digitalRead(BTN_BACK) == LOW);
  if (n && !prevNext) { stopNo = (stopNo + 1) % STOPS; announce(); }
  if (b && !prevBack) { stopNo = (stopNo + STOPS - 1) % STOPS; announce(); }
  prevNext = n;
  prevBack = b;
  delay(20);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Player not found: check wiring and the SD card.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power-upDing then the first stop name
NEXTDing then the next stop
BACKDing then the previous stop
After the last stopNEXT wraps to the first
Serial monitorPrints the stop name

If it does not work

Player not found message

Check TX and RX, the SD card and its format.

Wrong stop plays

Check the file names start with four digits.

Clicks or resets

Add a 100 microfarad capacitor across the player's power.

Too loud

Lower the volume number in the code.

Buttons do nothing

Check they go to D2 or D3 and GND.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the model tram stop announcer?

Arduino Nano, DFPlayer Mini MP3 module, Speaker 8 Ω 0.5 W, Tactile push button 6 mm × 2, Resistor 1 kΩ, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the model tram stop announcer take to build?

About 80 minutes for a intermediate maker, in 7 steps.

How do I know the model tram stop announcer works?

Power-up: Ding then the first stop name. NEXT: Ding then the next stop. BACK: Ding then the previous stop.

Player not found message: what should I check?

Check TX and RX, the SD card and its format.

Wrong stop plays: what should I check?

Check the file names start with four digits.

Clicks or resets: what should I check?

Add a 100 microfarad capacitor across the player's power.

Too loud: what should I check?

Lower the volume number in the code.