Tone decoder remote switch
Build it step by step
0 of 6 doneSet the timing
Wire pins 5 and 6, the 100 nF capacitor and the tuning pot.
Wire the filters and supply
Fit the two 10 µF capacitors and the supply decoupling.
Wire the LED
Connect the LED and 1 kΩ to pin 8.
Make a test tone
Use a phone tone-generator app set to about 800 Hz, played into the input potentiometer.
Tune
Adjust the timing pot until the LED lights when the tone plays.
Check the width
Move the tone away in 20 Hz steps and note where the LED drops out.
How do you build a tone decoder remote switch?
An LM567 lights an LED only when it hears one particular tone, which is the heart of simple audio remotes. You need LM567 tone decoder, Resistor 10 kΩ, Potentiometer 10 kΩ × 2, Ceramic Capacitor 100 nF × 2, Electrolytic capacitor 10 µF × 2, LED 5 mm red, Resistor 1 kΩ, Battery holder 4 × AA with switch, AA alkaline battery × 4 and Breadboard 830 Tie Points. It takes 6 steps and about 90 minutes.
- Level
- Intermediate
- Time
- About 90 min
- Parts
- 10
Parts list
- Integrated CircuitsBuy
- PassivesBuyResistor 10 kΩ × 1
- PassivesBuy
- PassivesBuy
- PassivesBuy
- SemiconductorsBuyLED 5 mm red × 1
- PassivesBuyResistor 1 kΩ × 1
- PowerBuy
- BatteriesBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 4 AA cells + | + rail | Supply of about 6 V (the LM567 maximum is 9 V) |
| 4 AA cells - | - rail | Ground |
| LM567 pin 4 (V+) | + rail | Power |
| LM567 pin 7 (GND) | - rail | Ground |
| 100 nF capacitor | + rail and - rail | Supply decoupling |
| 10 kΩ resistor and 10 kΩ potentiometer in series | Pin 5 and pin 6 | Timing resistor, tunes the frequency |
| 100 nF capacitor | Pin 6 and - rail | Timing capacitor (centre frequency about 1.1 ÷ (R × C)) |
| 10 µF capacitor | Pin 1 and - rail | Output filter |
| 10 µF capacitor | Pin 2 and - rail | Loop filter |
| Tone source via a 10 kΩ potentiometer | Wiper to a 10 µF capacitor then pin 3 | Input level control |
| 1 kΩ resistor then red LED | + rail to LED anode, LED cathode to pin 8 | Lights when a tone is detected |
No code needed
No code. LM567 pins: 1 output filter, 2 loop filter, 3 input, 4 V+, 5 and 6 timing, 7 GND, 8 output. Pin 8 pulls to ground when the input matches the tone. The chip's supply must stay between 4.75 V and 9 V, which is why four AA cells (about 6 V) are used, not a fresh 9 V battery. The centre frequency is about 1.1 ÷ (R × C), so 10 kΩ to 20 kΩ with 100 nF covers roughly 550 Hz to 1.1 kHz. For a microphone input use the electret preamp build.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| No tone | LED off |
| Tone at the set frequency | LED on |
| Tone 100 Hz away | LED off |
| Tone with a higher or lower level | Still detects until the level is too small |
If it does not work
LED always on
Input is too loud or timing is wrong. Lower the input level.
LED never lights
Check the frequency against 1.1 ÷ (R × C) and pin 3 coupling.
Flickers
Increase the loop filter capacitor on pin 2.
Chip hot
Supply is too high. Keep it at or below 9 V.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the tone decoder remote switch?
LM567 tone decoder, Resistor 10 kΩ, Potentiometer 10 kΩ × 2, Ceramic Capacitor 100 nF × 2, Electrolytic capacitor 10 µF × 2, LED 5 mm red, Resistor 1 kΩ, Battery holder 4 × AA with switch, AA alkaline battery × 4 and Breadboard 830 Tie Points.
How long does the tone decoder remote switch take to build?
About 90 minutes for a intermediate maker, in 6 steps.
How do I know the tone decoder remote switch works?
No tone: LED off. Tone at the set frequency: LED on. Tone 100 Hz away: LED off.
LED always on: what should I check?
Input is too loud or timing is wrong. Lower the input level.
LED never lights: what should I check?
Check the frequency against 1.1 ÷ (R × C) and pin 3 coupling.
Flickers: what should I check?
Increase the loop filter capacitor on pin 2.
Chip hot: what should I check?
Supply is too high. Keep it at or below 9 V.
