TDA2030 single-channel 18 W amplifier
Build it step by step
0 of 7 doneBuild the supply
Dual rail with decoupling.
Wire the chip
Pin 1 input, pin 4 output, pins 3 and 5 supply.
Set the gain
Feedback resistors.
Fit the heatsink
Insulated tab with paste.
Check the offset
Output near 0 V with a dummy resistor.
Connect the speaker
Play quiet music first.
Check the heat
After ten minutes the heatsink is warm, not hot.
How do you build a TDA2030 single-channel 18 W amplifier?
A TDA2030 power amplifier on a split supply drives a bookshelf speaker, with a heatsink and a proper star ground. You need TDA2030 audio amplifier, Heatsink TO-220, Dual-rail ±12 V DC-DC module, Resistor 100 kΩ, Resistor 4.7 kΩ, Resistor 22 kΩ, Electrolytic capacitor 22 µF, Electrolytic Capacitor 100 µF × 2, Ceramic Capacitor 100 nF × 2, Rectifier Diode 1N4007 × 2, Speaker 4 Ω 3 W and Perfboard (dot PCB) 7 × 9 cm. It takes 7 steps and about 180 minutes.
- Level
- Intermediate
- Time
- About 180 min
- Parts
- 12
Parts list
- Integrated CircuitsBuy
- Tools & InstrumentsBuyHeatsink TO-220 × 1
- Power
- PassivesBuyResistor 100 kΩ × 1
- PassivesBuyResistor 4.7 kΩ × 1
- PassivesBuyResistor 22 kΩ × 1
- PassivesBuy
- PassivesBuy
- PassivesBuy
- SemiconductorsBuy
- Motors & ActuatorsBuySpeaker 4 Ω 3 W × 1Use a speaker rated 15 W or more
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Input | 22 kΩ, then pin 1 | Non-inverting input |
| Pin 1 | 100 kΩ to ground | Input bias |
| Feedback from pin 4 | 22 kΩ to pin 2, and 680 Ω with 22 µF to ground | Gain about 33 |
| Pin 5 | Plus 12 V with 100 µF and 100 nF decoupling | Positive supply |
| Pin 3 | Minus 12 V with 100 µF and 100 nF decoupling | Negative supply |
| Pin 4 | Speaker plus, through a 1 Ω and 0.1 µF damping network | Output |
| Diodes | From pin 4 to each supply rail | Protection |
| Speaker minus | Star ground | Return |
No code needed
The TDA2030 is a power op-amp, so the gain follows the same feedback rule: about 1 plus 22 kΩ over 680 Ω, around 33 times. Decoupling capacitors sit right at the supply pins, otherwise the amplifier oscillates at high frequency. Bolt the metal tab to a heatsink with thermal paste, and note that the tab connects to the negative supply, so insulate the heatsink from the case or use a mica spacer. Run every ground back to one star point to avoid hum. Start with the speaker disconnected and a dummy resistor so you can check the output rests near zero volts; a sustained offset would damage the speaker. Use the small plus and minus 12 V module only within its current rating, a bookshelf speaker of at least 4 ohms, and never touch the heatsink or tab after a long run, since it gets hot.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Output rest voltage | Within 50 mV of zero |
| Music | Clean, no buzz |
| Heat | Warm heatsink at moderate volume |
| Ground | No hum from the star point |
If it does not work
Whine or buzz
Check decoupling and the star ground.
Hot quickly
Use a larger heatsink and lower the volume.
Offset voltage
Check the feedback and bias resistors.
Distorted
Reduce the input or check supply sag.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the TDA2030 single-channel 18 W amplifier?
TDA2030 audio amplifier, Heatsink TO-220, Dual-rail ±12 V DC-DC module, Resistor 100 kΩ, Resistor 4.7 kΩ, Resistor 22 kΩ, Electrolytic capacitor 22 µF, Electrolytic Capacitor 100 µF × 2, Ceramic Capacitor 100 nF × 2, Rectifier Diode 1N4007 × 2, Speaker 4 Ω 3 W and Perfboard (dot PCB) 7 × 9 cm. Speaker 4 Ω 3 W: Use a speaker rated 15 W or more.
How long does the TDA2030 single-channel 18 W amplifier take to build?
About 180 minutes for a intermediate maker, in 7 steps.
How do I know the TDA2030 single-channel 18 W amplifier works?
Output rest voltage: Within 50 mV of zero. Music: Clean, no buzz. Heat: Warm heatsink at moderate volume.
Whine or buzz: what should I check?
Check decoupling and the star ground.
Hot quickly: what should I check?
Use a larger heatsink and lower the volume.
Offset voltage: what should I check?
Check the feedback and bias resistors.
Distorted: what should I check?
Reduce the input or check supply sag.
