Build it step by step
0 of 7 doneDraw the circuit
Both channels.
Build the supply
Check plus and minus 9 V with a meter.
Fit the chip and decoupling
Pins 8 and 4.
Build one channel
Test with a phone and low volume.
Build the second channel
Same values.
Add the jacks
Check left and right.
Listen at low volume
Check for hiss and hum.
How do you build a headphone amplifier?
A NE5532 op-amp drives headphones with low noise from a ±9 V supply made with two batteries. You need NE5532 dual low-noise op-amp, Resistor 10 kΩ × 2, Resistor 4.7 kΩ × 2, Resistor 47 Ω × 2, Ceramic Capacitor 100 nF × 2, Electrolytic capacitor 220 µF × 2, Potentiometer 50 kΩ dual (stereo), Audio jack 3.5 mm (PCB, stereo) × 2, 9 V battery × 2, 9 V battery snap with DC jack × 2 and Perfboard (dot PCB) 7 × 9 cm. It takes 7 steps and about 150 minutes.
- Level
- Intermediate
- Time
- About 150 min
- Parts
- 11
Parts list
- Integrated CircuitsBuy
- PassivesBuyResistor 10 kΩ × 2
- PassivesBuyResistor 4.7 kΩ × 2
- PassivesBuyResistor 47 Ω × 2
- PassivesBuy
- PassivesBuy
- PassivesBuy
- ConnectorsBuy
- BatteriesBuy9 V battery × 2
- PowerBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Battery 1 plus | NE5532 pin 8 (V plus) | Plus 9 V rail |
| Battery 1 minus joined to battery 2 plus | Circuit ground (0 V) | Centre of the split supply |
| Battery 2 minus | NE5532 pin 4 (V minus) | Minus 9 V rail |
| 100 nF capacitors | Pin 8 to ground and pin 4 to ground, close to the chip | Decoupling |
| Input jack tip and ring (left, right) | 220 uF capacitor (plus toward the amp), then the volume pot ends | Input and volume |
| Volume pot wipers | NE5532 pin 3 (left) and pin 5 (right) | Non-inverting inputs |
| 10 k from pin 2 to pin 1, and 4.7 k from pin 2 to ground | Left channel, gain about 3 | Feedback network |
| 10 k from pin 6 to pin 7, and 4.7 k from pin 6 to ground | Right channel, gain about 3 | Feedback network |
| Pin 1 and pin 7 | 47 ohm resistor each, then the headphone jack tip and ring | Outputs (sleeve to ground) |
No code needed
The NE5532 is a dual low-noise op-amp, so one chip handles both stereo channels. It needs a supply above and below ground, which two 9 V batteries in series give with their joint as ground. Each channel is a non-inverting amplifier: the gain is one plus the feedback resistor over the resistor to ground, which with 10 k and 4.7 k is about 3.1, enough for a phone to drive headphones. The input capacitor stops DC from the source reaching the pot, the 47 ohm resistors at the output keep the op-amp stable and limit current, and the 100 nF capacitors next to the supply pins stop it oscillating. Build it on perfboard with short wires, keep the input wires away from the output, and fit a switch in the battery lead if you like. Hearing safety: start with the volume at minimum, raise it slowly, and never listen loudly for long, because this amp can drive headphones much louder than is safe. Connect the batteries last and the right way round, and use it with headphones of 32 ohm or more. There is no code.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Supply | About plus and minus 9 V from ground |
| Volume at zero | Silent, almost no hiss |
| Phone playing | Clean sound at both ears |
| Chip after a minute | Barely warm |
If it does not work
Hum or buzz
Shorten input wires and keep them away from the batteries.
One channel quiet
Check pins 1, 2, 3 or 5, 6, 7 of that channel.
Chip hot
Switch off and look for a short or oscillation.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the headphone amplifier?
NE5532 dual low-noise op-amp, Resistor 10 kΩ × 2, Resistor 4.7 kΩ × 2, Resistor 47 Ω × 2, Ceramic Capacitor 100 nF × 2, Electrolytic capacitor 220 µF × 2, Potentiometer 50 kΩ dual (stereo), Audio jack 3.5 mm (PCB, stereo) × 2, 9 V battery × 2, 9 V battery snap with DC jack × 2 and Perfboard (dot PCB) 7 × 9 cm.
How long does the headphone amplifier take to build?
About 150 minutes for a intermediate maker, in 7 steps.
How do I know the headphone amplifier works?
Supply: About plus and minus 9 V from ground. Volume at zero: Silent, almost no hiss. Phone playing: Clean sound at both ears.
Hum or buzz: what should I check?
Shorten input wires and keep them away from the batteries.
One channel quiet: what should I check?
Check pins 1, 2, 3 or 5, 6, 7 of that channel.
Chip hot: what should I check?
Switch off and look for a short or oscillation.
