Atari Punk Console noise synth
Build it step by step
0 of 7 donePlan the pins
NE556 pins 1 to 6 are timer 1, 8 to 13 are timer 2, 7 is ground and 14 is supply.
Build the astable
1 kΩ, pot 1 and 10 nF around pins 1, 2 and 6.
Build the monostable
Pot 2 and 10 nF around pins 11 and 12.
Couple them
10 nF from pin 5 to pin 8 with a 1 kΩ pull-up on pin 8.
Add the output
Pin 9 through 10 µF to the amplifier module and the speaker.
Play
Turn pot 1 for the pitch and pot 2 for the tone.
Experiment
Swap 10 nF for 100 nF or 1 nF to change the range.
How do you build an atari Punk Console noise synth?
Two 555 timers in a 556 make a classic lo-fi synth: one sets the pitch, the other the pulse width. You need NE556 dual timer, Potentiometer 10 kΩ × 2, Resistor 1 kΩ × 2, Ceramic capacitor 10 nF × 5, Electrolytic capacitor 10 µF, Ceramic Capacitor 100 nF, LM386 amplifier module, Speaker 8 Ω 0.5 W, 9 V battery, 9 V battery snap with DC jack, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 60 minutes.
- Level
- Beginner
- Time
- About 60 min
- Parts
- 12
Parts list
- Integrated CircuitsBuyNE556 dual timer × 1
- PassivesBuy
- PassivesBuyResistor 1 kΩ × 2
- PassivesBuy
- PassivesBuy
- PassivesBuy
- AudioBuy
- Motors & ActuatorsBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
- PrototypingBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery + | NE556 pin 14, amplifier module VCC | Supply |
| 9 V battery - | NE556 pin 7, amplifier GND | Ground |
| Timer 1 (astable) | 1 kΩ from +9 V to pin 1, pot 1 from pin 1 to pins 2 and 6 joined, 10 nF from there to GND | Sets the pitch |
| Pin 4 (reset 1) | +9 V | Not reset |
| Pin 3 and pin 10 (control voltage) | 10 nF to GND each | Decoupling |
| Pin 5 (output 1) | 10 nF coupling to pin 8, and 1 kΩ from pin 8 to +9 V | Trigger pulses to timer 2 |
| Timer 2 (monostable) | Pot 2 from +9 V to pins 11 and 12 joined, 10 nF from there to GND | Sets the pulse width |
| Pin 13 (reset 2) | +9 V | Not reset |
| Pin 9 (output 2) | 10 µF (+ to pin 9) to the amplifier input | Sound output |
| Amplifier module output | Speaker | Sound |
No code needed
No code. The first timer runs freely and sets the repetition rate. Each pulse triggers the second timer, which makes a pulse whose width is set by pot 2. When the pulse is longer than the interval, triggers are ignored, which gives the characteristic steps in pitch. Pot values of 10 kΩ with 10 nF give audible frequencies of a few kHz.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Pot 1 turned | Pitch changes smoothly |
| Pot 2 turned | Tone changes and the pitch steps |
| Both at extremes | Silence or a very high whine |
| Larger capacitors | Lower pitches |
If it does not work
No sound
Check supply on pins 14 and 7 and the amplifier connections.
Constant buzz, no variation
Pot 2 is at minimum so the pulse never ends. Turn it.
Hum or whine
Add decoupling, 100 nF across the supply, and keep wires short.
Distorted
Lower the amplifier's volume or gain.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the atari Punk Console noise synth?
NE556 dual timer, Potentiometer 10 kΩ × 2, Resistor 1 kΩ × 2, Ceramic capacitor 10 nF × 5, Electrolytic capacitor 10 µF, Ceramic Capacitor 100 nF, LM386 amplifier module, Speaker 8 Ω 0.5 W, 9 V battery, 9 V battery snap with DC jack, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).
How long does the atari Punk Console noise synth take to build?
About 60 minutes for a beginner maker, in 7 steps.
How do I know the atari Punk Console noise synth works?
Pot 1 turned: Pitch changes smoothly. Pot 2 turned: Tone changes and the pitch steps. Both at extremes: Silence or a very high whine.
No sound: what should I check?
Check supply on pins 14 and 7 and the amplifier connections.
Constant buzz, no variation: what should I check?
Pot 2 is at minimum so the pulse never ends. Turn it.
Hum or whine: what should I check?
Add decoupling, 100 nF across the supply, and keep wires short.
Distorted: what should I check?
Lower the amplifier's volume or gain.
