Superposition two-source lab
Build it step by step
0 of 7 doneBuild the network
Both sources through their resistors to a junction, then 4.7 kilohms to ground.
Measure with both sources
Note the junction voltage, about 7 V.
Remove the 6 V pack
Take the plus lead out and join the 2.2 kilohm resistor's free end to ground.
Measure
About 5.4 V, from the 9 V source alone.
Restore the 6 V pack and remove the 9 V battery
Join the 1 kilohm resistor's free end to ground.
Measure
About 1.6 V, from the 6 V pack alone.
Add the two answers
Compare the sum with the first reading.
How do you build a superposition two-source lab?
Build a small resistor network fed by a 9 V battery and a 6 V cell pack and measure one voltage with both sources on, then with each alone. The answer with both is the sum of the answers with each. You need Resistor 1 kΩ, Resistor 2.2 kΩ, Resistor 4.7 kΩ, Digital multimeter, 9 V battery, 9 V battery snap with DC jack, Battery holder 4 × AA with switch, AA alkaline battery × 4, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 50 minutes.
- Level
- Beginner
- Time
- About 50 min
- Parts
- 10
Parts list
- PassivesBuyResistor 1 kΩ × 1
- PassivesBuyResistor 2.2 kΩ × 1
- PassivesBuyResistor 4.7 kΩ × 1
- Tools & InstrumentsBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
- PowerBuy
- BatteriesBuy
- PrototypingBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery plus | 1 kilohm resistor to the junction | Source one |
| 6 V pack plus | 2.2 kilohm resistor to the junction | Source two |
| Junction | 4.7 kilohm resistor to the common ground rail, and the meter red probe | The node whose voltage we measure |
| Both battery minus leads | The common ground rail and the meter black probe | Shared reference |
| Meter dial | DC volts, 20 V range | Measures the junction voltage |
No code needed
No code. The junction voltage with both sources is Vn = (9/1000 + 6/2200) divided by (1/1000 + 1/2200 + 1/4700), which is about 7.03 V. With the 9 V source alone and the 6 V source replaced by a wire to ground, the junction is about 5.40 V. With the 6 V pack alone and the 9 V source replaced by a wire to ground, the junction is about 1.64 V. The two single-source answers add to 7.03 V, the same as with both on. This is the superposition rule, which holds for any circuit made of resistors and sources, and it lets you solve big circuits one source at a time. To switch a source off, take it out and join its connection to the ground rail with a wire, so its resistor goes straight to ground. Never join a battery's plus and minus together, which would be a short circuit.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Both sources on | About 7.0 V |
| 9 V source alone | About 5.4 V |
| 6 V pack alone | About 1.6 V |
| Sum of the two | About 7.0 V |
| Swap resistor values and repeat | The sum still matches |
If it does not work
Sum does not match
A source was not replaced by a wire to ground, or a joint is loose.
Readings drift
The cells are tired, so use fresh ones.
Voltage is much lower
Check the 4.7 kilohm resistor is connected to the ground rail.
Battery gets warm
Check there is no short between its plus and minus.
Meter reads negative
Swap the probes.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the superposition two-source lab?
Resistor 1 kΩ, Resistor 2.2 kΩ, Resistor 4.7 kΩ, Digital multimeter, 9 V battery, 9 V battery snap with DC jack, Battery holder 4 × AA with switch, AA alkaline battery × 4, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).
How long does the superposition two-source lab take to build?
About 50 minutes for a beginner maker, in 7 steps.
How do I know the superposition two-source lab works?
Both sources on: About 7.0 V. 9 V source alone: About 5.4 V. 6 V pack alone: About 1.6 V.
Sum does not match: what should I check?
A source was not replaced by a wire to ground, or a joint is loose.
Readings drift: what should I check?
The cells are tired, so use fresh ones.
Voltage is much lower: what should I check?
Check the 4.7 kilohm resistor is connected to the ground rail.
Battery gets warm: what should I check?
Check there is no short between its plus and minus.
