Projects / Supercapacitor charger and LED runtime test

Supercapacitor charger and LED runtime test

Beginner1 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. Check the cap is empty

    Meter reads under 0.1 V.

  2. Wire the charging path

    Diodes, resistor, capacitor.

  3. Connect the batteries

    Watch the voltage climb.

  4. Record voltage every 30 s

    Note when it levels off.

  5. Unplug the batteries

    Charging stops.

  6. 8.5 mA

    Connect the LED

    With the 220 ohm resistor.

  7. Time the glow

    Log voltage every 10 s.

In short

How do you build a supercapacitor charger and LED runtime test?

Charge a 10 F supercapacitor through a resistor and time how long it runs an LED, comparing with the RC time constant. You need Supercapacitor 2.7 V 10 F, Resistor 10 Ω, Signal Diode 1N4148 × 2, LED 5 mm red, Resistor 220 Ω, Digital multimeter, Battery holder 2 × AA and AA alkaline battery × 2. It takes 7 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
8
See the electronics first. This build uses capacitor charging. Try a capacitor charging in the circuit builder and watch the voltages and currents before you wire it.

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Battery holder plusTwo 1N4148 diodes in series, then the 10 ohm resistorDiodes drop about 1.2 V so the cap cannot be overcharged
10 ohm resistorSupercapacitor plus (long leg)Limits the charging current
Supercapacitor minus (marked stripe)Battery holder minusReturn path
MultimeterAcross the supercapacitorRead the voltage as it charges
LED with 220 ohm resistorAcross the charged supercapacitorDischarge test, after unplugging the battery

No code needed

A supercapacitor stores a huge charge, so charging is a slow RC curve: with 10 ohm and 10 F the time constant is 100 seconds, and it is about 95 percent charged after three of them, around five minutes. Its rating of 2.7 V is a hard limit, and two fresh AA cells give about 3.2 V, which is too much. The two diodes in series drop about 1.2 V, so the capacitor settles near 2 V and cannot go over, even if you forget it. Measure with the meter, not by guess. Energy stored is half times C times V squared, about 20 J at 2 V. Then unplug the battery, connect the LED with its resistor, and time how long it glows: the LED goes dim well before the voltage reaches zero, since a red LED needs about 1.8 V. Write the voltage every ten seconds and plot it to see the discharge curve. Never connect the supercapacitor backwards, and never short a charged one, because it can give a very large current for a moment and the wires will get hot. There is no code in this build.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
After 100 sAbout 60 percent of the final voltage
After 5 minutesClose to 2 V
LED connectedGlows for many minutes, then fades
PlotA smooth curve, not a straight line

If it does not work

Voltage rises slowly

Normal; check the resistor is 10 ohm, not 10 k.

LED very dim

The cap is below 1.8 V; that is the end of its use here.

Cap warm

Stop; check polarity.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the supercapacitor charger and LED runtime test?

Supercapacitor 2.7 V 10 F, Resistor 10 Ω, Signal Diode 1N4148 × 2, LED 5 mm red, Resistor 220 Ω, Digital multimeter, Battery holder 2 × AA and AA alkaline battery × 2.

How long does the supercapacitor charger and LED runtime test take to build?

About 60 minutes for a beginner maker, in 7 steps.

How do I know the supercapacitor charger and LED runtime test works?

After 100 s: About 60 percent of the final voltage. After 5 minutes: Close to 2 V. LED connected: Glows for many minutes, then fades.

Voltage rises slowly: what should I check?

Normal; check the resistor is 10 ohm, not 10 k.

LED very dim: what should I check?

The cap is below 1.8 V; that is the end of its use here.

Cap warm: what should I check?

Stop; check polarity.