Projects / Solar phone charger for a backpack

Solar phone charger for a backpack

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. SOLAR

    Test the panels

    Measure the open-circuit voltage in sun.

  2. SOLAR+

    Wire the panels in parallel

    Join the two plus and the two minus leads.

  3. CN3065+

    Connect the charger

    Check the charging light shows.

  4. +

    Insert the cell

    Check polarity first.

  5. +

    Connect the boost module

    Plug a USB meter into its output.

  6. +

    Measure a sunny day

    Note the mAh collected.

  7. SOLAR+

    Pack it

    Stitch the panels to a backpack flap and use a padded pouch.

In short

How do you build a solar phone charger for a backpack?

Two 6 V panels charge an 18650 cell by day through a solar charge chip, and a boost module gives 5 V USB for a phone. You need Solar panel 6 V 1 W × 2, CN3065 solar Li-ion charger module, 18650 cell 2600 mAh (branded), Battery holder 18650 single and 18650 battery charger and boost (5 V / 1 A). It takes 7 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Panel 1 + and Panel 2 +CN3065 IN+Panels in parallel
Panel 1 − and Panel 2 −CN3065 IN−Panels in parallel
CN3065 BAT+ and BAT−18650 holder + and −Cell charging
18650 holder + and −Boost module BAT+ and BAT−Cell to boost
Boost module USBPhone cable5 V output

No code needed

Two 1 W panels in parallel give about 330 mA at 6 V in full sun, so the cell fills slowly: a sunny day gives roughly 1000 to 1500 mAh, a fraction of a phone battery, so think of this as a top-up and an emergency charger rather than a replacement for a power bank. The CN3065 charges one lithium cell with a constant-current and constant-voltage profile, and the second module boosts to 5 V for USB at up to about 1 A. Panels in parallel keep the voltage at 6 V; do not wire two in series, which could exceed the charger's input limit. Use a protected 18650 cell, check polarity with a multimeter before inserting it, and never short it. Do not leave the pack in a closed hot car or in direct heat, and stop using it if the cell swells or gets hot. Keep the cell and boards in a padded case away from sharp objects. Measure the delivered mAh with a USB meter over a sunny day.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Panels in sunCharger LED shows charging
USB meter on the outputAbout 5 V with a phone connected
Phone chargingRate of 300 to 800 mA from the cell
A sunny dayAdds about 1000 mAh to the cell

If it does not work

No charging light

Check panel polarity and the sun angle.

Phone will not charge

Check the boost module's switch or button.

Very slow

Panels need direct sun and an angle facing it.

Cell very warm

Disconnect and check for a short.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the solar phone charger for a backpack?

Solar panel 6 V 1 W × 2, CN3065 solar Li-ion charger module, 18650 cell 2600 mAh (branded), Battery holder 18650 single and 18650 battery charger and boost (5 V / 1 A).

How long does the solar phone charger for a backpack take to build?

About 90 minutes for a beginner maker, in 7 steps.

How do I know the solar phone charger for a backpack works?

Panels in sun: Charger LED shows charging. USB meter on the output: About 5 V with a phone connected. Phone charging: Rate of 300 to 800 mA from the cell.

No charging light: what should I check?

Check panel polarity and the sun angle.

Phone will not charge: what should I check?

Check the boost module's switch or button.

Very slow: what should I check?

Panels need direct sun and an angle facing it.

Cell very warm: what should I check?

Disconnect and check for a short.