Projects / 18650 battery capacity tester

18650 battery capacity tester

Intermediate5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO+

    Check the cell first

    Use an undamaged, protected 18650 above 3.5 V. Never test a swollen or dented cell.

  2. NANOIRLZ44

    Build the discharge path

    Cell +, 10 Ω resistor, MOSFET drain, MOSFET source to cell -. Add a 10 kΩ from gate to GND.

  3. NANOIRLZ44

    Add the sense wires

    A0 to the cell +, A1 to the resistor-MOSFET junction, GND to the cell -.

  4. NANO15.4 mASSD1306

    Wire the Nano and display

    Gate to D4, button to D2, OLED on A4 and A5, power from USB.

  5. NANO

    Enter your own values

    Measure the resistor and the 5 V pin and set R_LOAD and VREF.

  6. NANO

    Start a test

    Press the button. Current is about 0.35 to 0.4 A. The display counts mAh until 3.0 V.

  7. NANO

    Compare

    A good 2600 mAh label should give at least 2000 mAh. A fake cell often gives less than half.

In short

How do you build a 18650 battery capacity tester?

A MOSFET and a power resistor discharge a cell at a steady current until 3.0 V while the Arduino counts milliamp-hours, exposing fake 'high capacity' cells. You need Arduino Nano, MOSFET IRLZ44N, Power resistor 10 Ω 5 W (cement), Resistor 10 kΩ, Battery holder 18650 single, SSD1306 OLED Display, Tactile push button 6 mm, USB A to micro-USB cable (data) and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 300 minutes.

Level
Intermediate
Time
About 300 min
Parts
9

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Cell +10 Ω power resistor and Nano A0Cell voltage
10 Ω resistor other endMOSFET drain and Nano A1Resistor current measured by the voltage drop
MOSFET sourceCell - and Nano GNDCommon ground
MOSFET gateNano D4, with 10 kΩ to GNDSwitches the load on and off
OLED SDA and SCLNano A4 and A5Display
Start buttonNano D2 and GNDBegin the test
Nano powerUSB cable from a computer or adapterThe cell is only the load

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install "Adafruit SSD1306" and "Adafruit GFX Library". Measure the real resistor value and the Nano's 5 V pin with a multimeter and enter them for accuracy. Only test undamaged cells with protection, stay nearby, and place the rig on a non-flammable surface. A 10 Ω resistor at 4.2 V dissipates about 1.8 W, so it gets hot.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>

Adafruit_SSD1306 oled(128, 64, &Wire, -1);
const byte GATE = 4, START = 2;
const float R_LOAD = 10.0;          // ohms, measure yours with a multimeter and enter it here
const float CUTOFF = 3.0;           // stop at this cell voltage
const float VREF = 5.0;             // measure the Nano's 5V pin and enter it here
float mAh = 0;
bool running = false;
unsigned long last = 0;

float volts(byte pin) {
  long s = 0;
  for (byte i = 0; i < 16; i++) s += analogRead(pin);
  return (s / 16.0) * VREF / 1023.0;
}

void setup() {
  pinMode(GATE, OUTPUT); digitalWrite(GATE, LOW);
  pinMode(START, INPUT_PULLUP);
  oled.begin(SSD1306_SWITCHCAPVCC, 0x3C);
  oled.setTextColor(SSD1306_WHITE);
}

void loop() {
  float vcell = volts(A0);
  float vdrain = volts(A1);
  float amps = (vcell - vdrain) / R_LOAD;      // current through the resistor

  if (!running && digitalRead(START) == LOW && vcell > CUTOFF + 0.2) {
    running = true; mAh = 0; last = millis(); digitalWrite(GATE, HIGH);
    delay(300);
  }
  if (running) {
    unsigned long now = millis();
    mAh += amps * 1000.0 * (now - last) / 3600000.0;
    last = now;
    if (vcell <= CUTOFF) { running = false; digitalWrite(GATE, LOW); }
  }

  oled.clearDisplay();
  oled.setTextSize(1); oled.setCursor(0, 0);
  oled.print(running ? "Discharging" : "Idle / done");
  oled.setCursor(0, 14); oled.print("Cell "); oled.print(vcell, 2); oled.print(" V");
  oled.setCursor(0, 26); oled.print("Current "); oled.print(amps * 1000, 0); oled.print(" mA");
  oled.setTextSize(2); oled.setCursor(0, 44); oled.print(mAh, 0); oled.print(" mAh");
  oled.display();
  delay(500);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Fully charged cell, startCurrent about 400 mA at 4.2 V, falling to about 300 mA at 3.0 V
Resistor temperatureHot but within its rating after a few minutes
End of testMOSFET switches off at 3.0 V and the display shows the total
Compare with a known good cellCapacity close to its label

If it does not work

Current reads zero

The gate is not high. Check D4 and the MOSFET orientation.

Result is far off

R_LOAD or VREF are not your measured values.

Resistor too hot

Mount it away from other parts and in free air. It is a 5 W part at under 2 W, but it still gets hot.

Test never starts

The cell is below the minimum starting voltage. Charge it first.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the 18650 battery capacity tester?

Arduino Nano, MOSFET IRLZ44N, Power resistor 10 Ω 5 W (cement), Resistor 10 kΩ, Battery holder 18650 single, SSD1306 OLED Display, Tactile push button 6 mm, USB A to micro-USB cable (data) and Jumper wires male to male (40 pcs, 20 cm).

How long does the 18650 battery capacity tester take to build?

About 300 minutes for a intermediate maker, in 7 steps.

How do I know the 18650 battery capacity tester works?

Fully charged cell, start: Current about 400 mA at 4.2 V, falling to about 300 mA at 3.0 V. Resistor temperature: Hot but within its rating after a few minutes. End of test: MOSFET switches off at 3.0 V and the display shows the total.

Current reads zero: what should I check?

The gate is not high. Check D4 and the MOSFET orientation.

Result is far off: what should I check?

R_LOAD or VREF are not your measured values.

Resistor too hot: what should I check?

Mount it away from other parts and in free air. It is a 5 W part at under 2 W, but it still gets hot.

Test never starts: what should I check?

The cell is below the minimum starting voltage. Charge it first.