Projects / SMD soldering practice

SMD soldering practice

Intermediate1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. 4.98V4.98V

    Set up

    Ventilation, iron stand and magnifier.

  2. Tin one pad

    A small amount of solder.

  3. 4.98V

    Place a resistor

    Hold it with tweezers.

  4. Solder both ends

    One side then the other.

  5. MMBT3904

    Solder a SOT-23

    First one pad, then the other two.

  6. 4.98V4.98V

    Fix a bridge

    Flux and wick.

  7. Inspect and score

    Count good and bad joints.

In short

How do you build an SMD soldering practice?

Practise soldering 0805 resistors and SOT-23 transistors with an iron, flux and tweezers. You need Soldering station (digital, 60 W), Soldering flux paste, Tweezers set (ESD safe), MOSFET AO3400A × 4, MMBT3904 NPN (SOT-23) × 4, Helping hands with magnifier and Desoldering wick (braid). It takes 7 steps and about 90 minutes.

Level
Intermediate
Time
About 90 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Iron temperatureAbout 320 to 350 degreesFast reflow without overheating
SolderThin 0.5 mm with flux coreSmall joints
FluxA little on every padWets and cleans
Part handlingESD-safe tweezersHold small parts
MagnifierHelping hands with lensInspect every joint
CleanupWick and isopropyl alcoholRemove bridges and residue

No code needed

This is a practice lab with no code. Use a scrap board or a practice PCB with empty pads. Tin one pad lightly, hold the part with tweezers, touch the iron to the tinned pad and the part together for a second, and let go; then solder the other side normally. For a SOT-23, tin one corner pad, solder that leg first, then the other two. Add flux to every pad because it helps the solder flow and pulls it into the joint. If you create a bridge between pads, add more flux, lay the wick on it, press the iron on the wick and slide away. Check each joint under the magnifier: a good joint looks like a small shiny cone, and a dull ball sitting on the pad is cold. Safety: work in a ventilated place or with a fume extractor, because flux smoke irritates the lungs; the iron is hot enough to burn at once, so keep it in its stand; wash hands after handling leaded solder; and wear safety glasses, as small parts and solder spatter can fly.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Resistor jointsSmall shiny cones on both ends
SOT-23All three legs wetted and straight
Bridge removedPads cleanly separate
PartDoes not move when nudged

If it does not work

Part flies away

Hold it down while the first side cools.

Solder balls up

Add flux and clean the tip.

Pad lifts

Use less heat and time.

Bridges everywhere

Use less solder and more flux.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the SMD soldering practice?

Soldering station (digital, 60 W), Soldering flux paste, Tweezers set (ESD safe), MOSFET AO3400A × 4, MMBT3904 NPN (SOT-23) × 4, Helping hands with magnifier and Desoldering wick (braid).

How long does the SMD soldering practice take to build?

About 90 minutes for a intermediate maker, in 7 steps.

How do I know the SMD soldering practice works?

Resistor joints: Small shiny cones on both ends. SOT-23: All three legs wetted and straight. Bridge removed: Pads cleanly separate.

Part flies away: what should I check?

Hold it down while the first side cools.

Solder balls up: what should I check?

Add flux and clean the tip.

Pad lifts: what should I check?

Use less heat and time.

Bridges everywhere: what should I check?

Use less solder and more flux.