Projects / Design a 3D printed enclosure

Design a 3D printed enclosure

Intermediate3 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. Measure the board

    Length, width and holes.

  2. Measure the connectors

    Heights and offsets.

  3. BRASS

    Model the base

    Walls and standoffs.

  4. Add openings

    Slightly oversize.

  5. Model the lid

    Lip plus tabs or screws.

  6. Print a small test

    Corner and connector.

  7. Print and fit

    Adjust the tolerance.

In short

How do you build a design a 3D printed enclosure?

Measure your board, design a snap-fit case with openings and print it. You need Digital vernier caliper, 3D printer (FDM, 220 mm bed), 3D printer PLA filament 1.75 mm (1 kg) and Brass spacer kit M3 (standoffs). It takes 7 steps and about 180 minutes.

Level
Intermediate
Time
About 180 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Board outlineLength, width and thickness from the caliperInner size of the case
Mounting holesPosition and diameterStandoff positions
ConnectorsHeight and offset from the board edgeOpenings in the walls
Clearance0.3 mm per sidePrint tolerance
Wall thickness2 mmStrength
LidSnap tabs or M3 screwsClosing

No code needed

This is a design lab with no code. Measure the board with the caliper: its length, width, the position and size of each mounting hole, and the height and offset of the USB connector, buttons and LEDs. In your CAD program, model the base as a box that is 0.3 mm bigger on each side than the board, with 2 mm walls and four standoff posts that match the holes; cut openings for the connectors a little oversize; then make a lid with a lip that fits inside the walls, using either two small snap tabs or four M3 screws into heat-set or self-tapping holes. Print a quick test of only the corner and one connector before the full case. Use PLA at 0.2 mm layers; print the base upright and the lid flat for a smooth top. Print and test fit, then change the clearances in your model until the board drops in without force. Never leave a printer running unattended, keep it ventilated and away from anything flammable, and do not touch the hot nozzle or bed.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
BoardDrops in without force
ConnectorsLine up with the openings
LidCloses with a click
StandoffsHold the board without bending

If it does not work

Board does not fit

Add 0.1 mm clearance and reprint.

Holes too small

Open them by 0.2 mm in the model.

Lid loose

Make the lip thicker by 0.1 mm.

Warping

Use a brim and print away from drafts.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the design a 3D printed enclosure?

Digital vernier caliper, 3D printer (FDM, 220 mm bed), 3D printer PLA filament 1.75 mm (1 kg) and Brass spacer kit M3 (standoffs).

How long does the design a 3D printed enclosure take to build?

About 180 minutes for a intermediate maker, in 7 steps.

How do I know the design a 3D printed enclosure works?

Board: Drops in without force. Connectors: Line up with the openings. Lid: Closes with a click.

Board does not fit: what should I check?

Add 0.1 mm clearance and reprint.

Holes too small: what should I check?

Open them by 0.2 mm in the model.

Lid loose: what should I check?

Make the lip thicker by 0.1 mm.

Warping: what should I check?

Use a brim and print away from drafts.