Projects / Voice-style multi kitchen timers

Voice-style multi kitchen timers

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Test the display

    Print four lines.

  2. NANO

    Read the encoder

    Change minutes.

  3. NANO

    Add the press logic

    Short and long press.

  4. NANO

    Count down

    Four timers in the loop.

  5. NANO12.2 mA

    Add the LEDs

    Light while running.

  6. NANO

    Add the beeps

    A different count for each timer.

  7. NANO

    Box it

    Wipe-clean front panel.

In short

How do you build a voice-style multi kitchen timers?

Four timers for different pots, each with its own LED and sound, set by an encoder. You need Arduino Nano, Rotary encoder module (KY-040), 20x4 LCD with I2C backpack, LED 5 mm red × 4, Resistor 220 Ω × 4 and Active buzzer 5 V. It takes 7 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Encoder CLK and DTNano D2 and D3Turn input
Encoder SWNano D4Press input
LCD SDA and SCLNano A4 and A5Display
Timer LEDsNano D5 to D8 through 220 ΩOne per timer
BuzzerNano D9 and GNDBeeper
SupplyUSB or a 5 V adapterPower

Code

Each timer is just a countdown number checked once a second, with the display and LEDs updated from the same loop, so all four run together without blocking each other. The number of beeps tells you which timer has finished: one for timer 1, two for timer 2, and so on. The sketch assumes a 20 by 4 I2C LCD at address 0x27; if yours is at 0x3F or has a different size, change that line. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails). Keep the Nano and the display away from steam and splashes, and do not use it as the only safeguard for anything that could be a fire risk, such as hot oil.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Four kitchen timers. Turn = set minutes for the selected timer. Short press = start/stop. Long press = next timer.
// Libraries: LiquidCrystal_I2C, Encoder. Board: Arduino Nano.
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
#include <Encoder.h>
LiquidCrystal_I2C lcd(0x27, 20, 4);
Encoder enc(2, 3);
const int SW = 4, BUZ = 9;
const int LED[4] = {5, 6, 7, 8};
long setSec[4] = {600, 600, 600, 600};
long leftSec[4] = {600, 600, 600, 600};
bool running[4] = {false, false, false, false};
unsigned long last = 0, pressAt = 0;
int sel = 0;
long lastPos = 0;
void beep(int n) { for (int i = 0; i < n; i++) { tone(BUZ, 1500, 150); delay(250); } }
void draw() {
  for (int i = 0; i < 4; i++) {
    lcd.setCursor(0, i);
    lcd.print(i == sel ? ">" : " ");
    lcd.print("T"); lcd.print(i + 1); lcd.print(" ");
    long s = running[i] ? leftSec[i] : setSec[i];
    if (s / 60 < 10) lcd.print("0");
    lcd.print(s / 60); lcd.print(":");
    if (s % 60 < 10) lcd.print("0");
    lcd.print(s % 60); lcd.print(running[i] ? " run " : " set ");
  }
}
void setup() {
  pinMode(SW, INPUT_PULLUP); pinMode(BUZ, OUTPUT);
  for (int i = 0; i < 4; i++) pinMode(LED[i], OUTPUT);
  lcd.init(); lcd.backlight(); draw();
}
void loop() {
  long pos = enc.read() / 4;
  if (pos != lastPos) {
    if (!running[sel]) { setSec[sel] = constrain(setSec[sel] + (pos - lastPos) * 60, 60, 5940); leftSec[sel] = setSec[sel]; }
    lastPos = pos; draw();
  }
  if (digitalRead(SW) == LOW && pressAt == 0) pressAt = millis();
  if (digitalRead(SW) == HIGH && pressAt) {
    unsigned long held = millis() - pressAt; pressAt = 0;
    if (held > 40) {
      if (held > 700) sel = (sel + 1) % 4;                    // long press: next timer
      else { running[sel] = !running[sel]; if (running[sel]) leftSec[sel] = setSec[sel]; }
      draw();
    }
  }
  if (millis() - last >= 1000) {
    last = millis();
    for (int i = 0; i < 4; i++) {
      digitalWrite(LED[i], running[i]);
      if (running[i] && --leftSec[i] <= 0) {
        running[i] = false; leftSec[i] = setSec[i];
        int keep = sel; sel = i; beep(i + 1); sel = keep;    // timer 1 beeps once, timer 2 twice, and so on
        draw();
      }
    }
    if (millis() > 0) draw();
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Turn the encoderMinutes change for the selected timer
Short pressStarts or stops
Long pressMoves to the next timer
FinishThe right number of beeps

If it does not work

Blank LCD

Try address 0x3F and adjust the contrast.

Encoder skips

Change the divisor of 4 to match your encoder.

Wrong beeps

Check the timer number mapping.

Time runs off

Use an RTC for long timers.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the voice-style multi kitchen timers?

Arduino Nano, Rotary encoder module (KY-040), 20x4 LCD with I2C backpack, LED 5 mm red × 4, Resistor 220 Ω × 4 and Active buzzer 5 V.

How long does the voice-style multi kitchen timers take to build?

About 90 minutes for a beginner maker, in 7 steps.

How do I know the voice-style multi kitchen timers works?

Turn the encoder: Minutes change for the selected timer. Short press: Starts or stops. Long press: Moves to the next timer.

Blank LCD: what should I check?

Try address 0x3F and adjust the contrast.

Encoder skips: what should I check?

Change the divisor of 4 to match your encoder.

Wrong beeps: what should I check?

Check the timer number mapping.

Time runs off: what should I check?

Use an RTC for long timers.