Projects / Simon-style memory game

Simon-style memory game

Beginner2 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. UNO14.6 mA

    Test one LED

    Wire the red LED with its resistor to D2 and run a one-line blink.

  2. UNO14.7 mA

    Add the other three LEDs

    Same pattern on D3, D4 and D5.

  3. UNO

    Wire the four buttons

    Each between a pin and GND.

  4. UNO

    Add the buzzer

    Between D10 and GND.

  5. UNO

    Upload the sketch

    You should see a start-up sweep.

  6. UNO

    Play three rounds

    Check the order and the sounds.

  7. UNO

    Try a wrong press

    Check the game-over flash.

  8. UNO14.7 mA

    Mount it on a card or box

    Match each button to its LED.

In short

How do you build a simon-style memory game?

Four coloured LEDs flash a growing pattern that you repeat on four buttons, with a different beep for each colour. You need Arduino Uno R3, LED 5 mm red, LED 5 mm green, LED 5 mm blue, LED 5 mm yellow, Tactile push button 6 mm × 4, Passive buzzer, Resistor 220 Ω × 4, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 8 steps and about 120 minutes.

Level
Beginner
Time
About 120 min
Parts
10

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Red LED plusUno D2 through a 220 ohm resistor, minus to GNDColour 1
Green LED plusUno D3 through a 220 ohm resistor, minus to GNDColour 2
Blue LED plusUno D4 through a 220 ohm resistor, minus to GNDColour 3
Yellow LED plusUno D5 through a 220 ohm resistor, minus to GNDColour 4
Four buttons, one side eachUno D6, D7, D8, D9, other side to GNDInternal pull-ups, pressed reads LOW
Passive buzzer plus and minusUno D10 and GNDDifferent tone per colour
Uno A0Leave unconnectedFloating pin gives a random seed

Code

The Uno keeps the pattern in an array. Each round it adds one random colour, replays the whole pattern with a different tone per LED, then waits for you to press the same buttons in order. A wrong press, or no press for five seconds, plays a low tone and flashes all LEDs, and the game starts again from one colour. The playback speeds up as the pattern grows, and a complete 24-step run counts as a win. Buttons use the Uno's internal pull-ups, so each one connects a pin to ground and a press reads LOW. The random seed comes from the unconnected A0 pin, so each game is different. Each LED has its own 220 ohm resistor, which keeps the current near 10 mA, well inside the Uno's limit. Use the passive buzzer, which makes the different notes. An active buzzer would make only one sound. Setup: Arduino IDE, board "Arduino Uno". No extra libraries are needed.

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t LED[4] = {2, 3, 4, 5};
const uint8_t BTN[4] = {6, 7, 8, 9};
const uint8_t BUZ = 10;
const int TONE_HZ[4] = {262, 330, 392, 523};     // C, E, G, high C
const uint8_t MAX_LEN = 24;

uint8_t seq[MAX_LEN];
uint8_t len = 0;

void flash(uint8_t i, unsigned int ms) {
  digitalWrite(LED[i], HIGH);
  tone(BUZ, TONE_HZ[i]);
  delay(ms);
  noTone(BUZ);
  digitalWrite(LED[i], LOW);
  delay(80);
}

// Returns the button number that was pressed, or -1 after the timeout.
int waitPress(unsigned long timeoutMs) {
  unsigned long t0 = millis();
  while (millis() - t0 < timeoutMs) {
    for (uint8_t i = 0; i < 4; i++) {
      if (digitalRead(BTN[i]) == LOW) {
        digitalWrite(LED[i], HIGH);
        tone(BUZ, TONE_HZ[i]);
        while (digitalRead(BTN[i]) == LOW) { }   // hold the light and tone until release
        noTone(BUZ);
        digitalWrite(LED[i], LOW);
        delay(40);                               // simple debounce
        return i;
      }
    }
  }
  return -1;
}

void gameOver() {
  tone(BUZ, 120, 600);
  for (uint8_t k = 0; k < 3; k++) {
    for (uint8_t i = 0; i < 4; i++) digitalWrite(LED[i], HIGH);
    delay(200);
    for (uint8_t i = 0; i < 4; i++) digitalWrite(LED[i], LOW);
    delay(200);
  }
  len = 0;
  delay(1000);
}

void setup() {
  for (uint8_t i = 0; i < 4; i++) {
    pinMode(LED[i], OUTPUT);
    pinMode(BTN[i], INPUT_PULLUP);
  }
  pinMode(BUZ, OUTPUT);
  randomSeed(analogRead(A0));
  // Start-up sweep so you know it is alive
  for (uint8_t i = 0; i < 4; i++) flash(i, 120);
  delay(500);
}

void loop() {
  if (len < MAX_LEN) seq[len++] = random(4);
  unsigned int ms = max(120, 420 - len * 14);          // gets faster as the pattern grows
  delay(400);
  for (uint8_t k = 0; k < len; k++) flash(seq[k], ms);

  for (uint8_t k = 0; k < len; k++) {
    int p = waitPress(5000);                           // five seconds to answer
    if (p != seq[k]) { gameOver(); return; }
  }
  if (len == MAX_LEN) {                                // you won: celebrate and restart
    for (uint8_t i = 0; i < 4; i++) flash(i, 100);
    for (uint8_t i = 0; i < 4; i++) flash(3 - i, 100);
    len = 0;
    delay(1000);
  } else {
    delay(500);
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power onLEDs sweep once with four notes
Round 1One LED flashes, then you repeat it
Press the wrong buttonLow tone, all LEDs flash, restart
Wait 5 seconds without pressingSame game-over
Play to step 6Playback is noticeably faster

If it does not work

Nothing happens

Check the USB cable and board selection.

A button is always pressed

The wire goes to the wrong pin or the button is rotated.

No sound

Check the buzzer polarity and that it is a passive type.

LED dim or off

LED the wrong way round, or a missing resistor.

Same pattern every game

A0 is connected to something, leave it floating.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the simon-style memory game?

Arduino Uno R3, LED 5 mm red, LED 5 mm green, LED 5 mm blue, LED 5 mm yellow, Tactile push button 6 mm × 4, Passive buzzer, Resistor 220 Ω × 4, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the simon-style memory game take to build?

About 120 minutes for a beginner maker, in 8 steps.

How do I know the simon-style memory game works?

Power on: LEDs sweep once with four notes. Round 1: One LED flashes, then you repeat it. Press the wrong button: Low tone, all LEDs flash, restart.

Nothing happens: what should I check?

Check the USB cable and board selection.

A button is always pressed: what should I check?

The wire goes to the wrong pin or the button is rotated.

No sound: what should I check?

Check the buzzer polarity and that it is a passive type.

LED dim or off: what should I check?

LED the wrong way round, or a missing resistor.