Projects / Robot that follows you

Robot that follows you

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. UNOROBOT+

    Assemble the chassis

    Motors, wheels, caster, holder.

  2. UNO

    Wire the L298N and Uno

    As in the table, wheels in the air.

  3. UNO

    Test the motors alone

    Check each wheel direction.

  4. UNO71 cm

    Add the ultrasonic sensor

    Print distances first.

  5. UNO

    Add the two IR sensors

    Trim them for about 30 cm.

  6. UNO

    Upload the follow sketch

    Try it in your hand first.

  7. UNO

    Test on the floor

    Walk slowly in front.

  8. UNO

    Tune the speeds and distances

    Keep them gentle.

In short

How do you build a robot that follows you?

An ultrasonic sensor in the middle and IR sensors on the sides let a small robot follow a hand or a person at a set distance. You need Arduino Uno R3, HC-SR04 Ultrasonic Sensor, IR obstacle avoidance sensor module × 2, L298N Dual H-Bridge Module, Robot car chassis kit 2WD (acrylic), Battery holder 18650 2S (series), 18650 cell 2600 mAh (branded) × 2 and Jumper wires male to male (40 pcs, 20 cm). It takes 8 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
18650 holder (2 cells in series) plusL298N 12V terminalMotor supply, 7.4 to 8.4 V
18650 holder minusL298N GND and Uno GNDCommon ground
L298N 5V terminalUno 5V pinPowers the Uno, keep the regulator jumper on
Uno D5, D7, D8L298N ENA, IN1, IN2Left motor
Uno D6, D9, D10L298N ENB, IN3, IN4Right motor
HC-SR04 TRIG, ECHOUno D2, D3Front distance
Left IR sensor OUTUno D11Goes LOW when it sees you
Right IR sensor OUTUno D12Goes LOW when it sees you
All sensors VCC and GNDUno 5V and GNDPower

Code

This robot keeps a polite distance. The ultrasonic sensor measures how far away you are. Between 30 and 100 cm the robot drives forward faster the farther you are (proportional control), inside 30 cm it holds still, and inside 15 cm it backs away. The two IR obstacle sensors on the front corners tell it which side you are on: when you are on the left, the left wheel slows so the robot curves toward you. If it cannot see you ahead but one side sensor can, it spins towards that side, and if nothing is seen it stops, which is the safe default. The speeds are kept modest so it cannot chase anyone fast, and you should always test it with the wheels in the air first. IR sensors work poorly in direct sunlight and on black clothes, and ultrasonic sensors can miss thin legs, so expect it to lose you sometimes; stop-on-nothing is deliberate. Keep it away from stairs, pets and small children. Adjust the little trimmer on each IR module until it detects you at about 30 cm. Power from two 18650 cells in a holder through the L298N, which also supplies 5 V to the Uno (leave its regulator jumper on). Use protected cells and never leave them charging unattended. Setup: Arduino IDE, board "Arduino Uno".

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t TRIG = 2, ECHO = 3, IR_L = 11, IR_R = 12;
const uint8_t ENA = 5, IN1 = 7, IN2 = 8, ENB = 6, IN3 = 9, IN4 = 10;
const int STOP_NEAR = 15, HOLD_MIN = 30, FOLLOW_MAX = 100;    // distances in cm
const int SPEED_MIN = 110, SPEED_MAX = 200;                    // PWM, kept modest on purpose

int readCm() {
  digitalWrite(TRIG, LOW);  delayMicroseconds(2);
  digitalWrite(TRIG, HIGH); delayMicroseconds(10);
  digitalWrite(TRIG, LOW);
  unsigned long us = pulseIn(ECHO, HIGH, 15000UL);
  return us ? us / 58 : 999;
}

void motor(uint8_t en, uint8_t a, uint8_t b, int speed) {      // speed -255 to 255
  digitalWrite(a, speed > 0);
  digitalWrite(b, speed < 0);
  analogWrite(en, abs(speed));
}

void drive(int left, int right) { motor(ENA, IN1, IN2, left); motor(ENB, IN3, IN4, right); }

void setup() {
  pinMode(TRIG, OUTPUT); pinMode(ECHO, INPUT);
  pinMode(IR_L, INPUT);  pinMode(IR_R, INPUT);
  uint8_t outs[] = {ENA, IN1, IN2, ENB, IN3, IN4};
  for (uint8_t p : outs) pinMode(p, OUTPUT);
  drive(0, 0);
}

void loop() {
  int d = readCm();
  bool left = !digitalRead(IR_L);              // modules are active low
  bool right = !digitalRead(IR_R);

  if (d < STOP_NEAR) {                         // too close: back away slowly
    drive(-SPEED_MIN, -SPEED_MIN);
  } else if (d <= HOLD_MIN) {                  // in the sweet spot: hold position
    drive(0, 0);
  } else if (d <= FOLLOW_MAX) {                // follow, faster the farther you are
    int v = map(d, HOLD_MIN, FOLLOW_MAX, SPEED_MIN, SPEED_MAX);
    int l = v, r = v;
    if (left && !right)  { l = v / 3; }        // you are on the left: slow the left wheel to turn left
    if (right && !left)  { r = v / 3; }
    drive(l, r);
  } else if (left && !right) {                // lost ahead but seen on one side: spin towards it
    drive(-SPEED_MIN, SPEED_MIN);
  } else if (right && !left) {
    drive(SPEED_MIN, -SPEED_MIN);
  } else {
    drive(0, 0);                               // nothing seen: stop
  }
  delay(40);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Hand 20 cm in frontRobot holds still
Hand at 60 cmRobot drives forward at medium speed
Hand 10 cm awayRobot backs off
Hand moved to the left sideRobot curves left
Remove everythingRobot stops

If it does not work

Robot spins or twitches

Motors wired backwards; swap the pair on that side.

Never follows

Check the HC-SR04 pins and that you are within 100 cm.

Chases a wall

Ultrasonic sees the wall; keep the area clear or lower FOLLOW_MAX.

IR always on

Trimmer too sensitive; turn it down.

Uno resets when motors start

Weak cells or a loose connection; fully charge the cells.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the robot that follows you?

Arduino Uno R3, HC-SR04 Ultrasonic Sensor, IR obstacle avoidance sensor module × 2, L298N Dual H-Bridge Module, Robot car chassis kit 2WD (acrylic), Battery holder 18650 2S (series), 18650 cell 2600 mAh (branded) × 2 and Jumper wires male to male (40 pcs, 20 cm).

How long does the robot that follows you take to build?

About 150 minutes for a intermediate maker, in 8 steps.

How do I know the robot that follows you works?

Hand 20 cm in front: Robot holds still. Hand at 60 cm: Robot drives forward at medium speed. Hand 10 cm away: Robot backs off.

Robot spins or twitches: what should I check?

Motors wired backwards; swap the pair on that side.

Never follows: what should I check?

Check the HC-SR04 pins and that you are within 100 cm.

Chases a wall: what should I check?

Ultrasonic sees the wall; keep the area clear or lower FOLLOW_MAX.

IR always on: what should I check?

Trimmer too sensitive; turn it down.