Projects / Pull-down versus pull-up inputs

Pull-down versus pull-up inputs

Wire one button with a pull-down resistor and a second with a pull-up and see that one reads high when pressed and the other reads low. A third button with no resistor at all reads random values, which makes the idea of a floating input clear.

Beginner50 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Wire button A with its pull-down

    D2 reads 0 until pressed.

  2. NANO

    Wire button B with its pull-up

    D3 reads 1 until pressed.

  3. NANO

    Wire button C with no resistor

    Leave D4 floating.

  4. NANO

    Upload and open the serial monitor at 9600

    A table header appears.

  5. NANO11.7 mA

    Press A and B in turn

    A reads 1, B reads 0, and the LEDs light.

  6. NANO

    Watch C with no press and bring a finger near

    The reading wanders.

  7. NANO

    Switch D4 to INPUT_PULLUP and move C to GND

    The reading becomes steady.

In short

How do you build a pull-down versus pull-up inputs?

Wire one button with a pull-down resistor and a second with a pull-up and see that one reads high when pressed and the other reads low. A third button with no resistor at all reads random values, which makes the idea of a floating input clear. You need Arduino Nano, Tactile push button 6 mm × 3, Resistor 10 kΩ × 2, LED 5 mm red × 2, Resistor 220 Ω × 2, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 50 minutes.

Level
Beginner
Time
About 50 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Button A leg 1Nano 5VPull-down button: pressing sends 5 V to D2
Button A leg 2Nano D2 and a 10 kilohm resistor to GNDThe resistor holds D2 low when idle
Button B leg 1Nano GNDPull-up button: pressing sends ground to D3
Button B leg 2Nano D3 and a 10 kilohm resistor to 5VThe resistor holds D3 high when idle
Button C leg 1Nano 5VFloating button: no resistor on the other side
Button C leg 2Nano D4 onlyNothing holds D4 when the button is open
LED 1 long legNano D8 through a 220 ohm resistor, short leg to GNDFollows button A
LED 2 long legNano D9 through a 220 ohm resistor, short leg to GNDFollows button B

Code

A digital input that is connected to nothing is said to float, and it picks up stray electricity from the air and your fingers, so it reads high or low at random. A resistor of about 10 kilohms fixes that. A pull-down resistor to ground holds the pin low until a button joins it to 5 volts, so the pin reads 1 when pressed. A pull-up resistor to 5 volts holds it high until a button joins it to ground, so the pin reads 0 when pressed. Button C has neither, so D4 reads a jumble that changes if you bring a finger near the wire. The sketch prints all three values whenever any of them changes, and lights the two LEDs while A and B are pressed. Once you have seen the floating pin misbehave, change INPUT to INPUT_PULLUP for D4, move button C's first leg to GND, and see that the Nano's own built-in pull-up does the job without any resistor. Never join 5 volts to ground with a button and no resistor on a pin set as an output.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t PULL_DOWN_PIN = 2;   // button A, external pull-down
const uint8_t PULL_UP_PIN   = 3;   // button B, external pull-up
const uint8_t FLOAT_PIN     = 4;   // button C, no resistor at all
const uint8_t LED_A = 8;
const uint8_t LED_B = 9;

int lastA = -1, lastB = -1, lastC = -1;

void setup() {
  pinMode(PULL_DOWN_PIN, INPUT);
  pinMode(PULL_UP_PIN, INPUT);
  pinMode(FLOAT_PIN, INPUT);        // try INPUT_PULLUP here later and compare
  pinMode(LED_A, OUTPUT);
  pinMode(LED_B, OUTPUT);
  Serial.begin(9600);
  Serial.println("A (pull-down)  B (pull-up)  C (floating)");
}

void loop() {
  int a = digitalRead(PULL_DOWN_PIN);   // 0 idle, 1 pressed
  int b = digitalRead(PULL_UP_PIN);     // 1 idle, 0 pressed
  int c = digitalRead(FLOAT_PIN);       // random when idle
  digitalWrite(LED_A, a);               // lit while A is pressed
  digitalWrite(LED_B, !b);              // lit while B is pressed
  if (a != lastA || b != lastB || c != lastC) {
    lastA = a; lastB = b; lastC = c;
    Serial.print(a); Serial.print("              ");
    Serial.print(b); Serial.print("            ");
    Serial.println(c);
  }
  delay(20);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

A (pull-down)  B (pull-up)  C (floating)
0              0            0

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
A idle and pressed0 then 1
B idle and pressed1 then 0
C openChanges randomly, especially near a finger
C with INPUT_PULLUP and GNDSteady 1, then 0 when pressed
LEDsLight only while their button is held

If it does not work

A or B reads the wrong way

Check which side the resistor and the button go to.

Both LEDs stay dark

Check the LED direction and the 220 ohm resistors.

C looks steady

Hold a finger near the wire, or touch the metal lead.

Readings are always 1

Check the button is not stuck or wired across 5V and D4.

No serial text

Set 9600 baud.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the pull-down versus pull-up inputs?

Arduino Nano, Tactile push button 6 mm × 3, Resistor 10 kΩ × 2, LED 5 mm red × 2, Resistor 220 Ω × 2, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the pull-down versus pull-up inputs take to build?

About 50 minutes for a beginner maker, in 7 steps.

How do I know the pull-down versus pull-up inputs works?

A idle and pressed: 0 then 1. B idle and pressed: 1 then 0. C open: Changes randomly, especially near a finger.

A or B reads the wrong way: what should I check?

Check which side the resistor and the button go to.

Both LEDs stay dark: what should I check?

Check the LED direction and the 220 ohm resistors.

C looks steady: what should I check?

Hold a finger near the wire, or touch the metal lead.

Readings are always 1: what should I check?

Check the button is not stuck or wired across 5V and D4.