Projects / Fuse and polyfuse lab

Fuse and polyfuse lab

Beginner1 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. 4.98V

    Set the supply

    5 V with the current limit at the test value.

  2. Fit the fuse in the holder

    Closed holder or clear box.

  3. 4.98V

    Switch on and time

    Start the stopwatch at power on.

  4. Repeat at 2 times

    A fresh fuse each time.

  5. Repeat at 3 times

    A fresh fuse again.

  6. Test the polyfuse

    See it reset after cooling.

  7. Plot the results

    Time against current.

In short

How do you build a fuse and polyfuse lab?

Blow a few fuses at different currents to see how long each takes and choose the right fuse. You need Fuse 1 A glass (5 × 20 mm) × 3, Polyfuse (PTC resettable) 500 mA, Bench power supply 30 V 5 A and Resistor 10 kΩ. It takes 7 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Bench supply plusFuse holder, then the test leadPositive through the fuse
Test leadA short link back to the supplyShort circuit through the fuse
Bench supply minusReturn leadReturn
Voltage knob5 VKeep the voltage low
Current limit knobSet the test current (1.5 A, 2 A, 3 A)Constant-current mode
Phone stopwatchStart when the output turns onTime to blow

No code needed

This is a hands-on lab with no code. Set the supply to 5 V and turn the current limit to the test current before connecting; shorting the output through the fuse then makes the supply hold exactly that current. Run 1.5 times, 2 times and 3 times the 1 A rating on separate fuses, time each one until the fuse opens, and plot time against current. A fast glass fuse reacts quickly at high current but takes a long time, or never opens, at 1.5 times its rating, which is why a fuse protects wires and not delicate chips. Then repeat with the polyfuse, which warms up, goes to a high resistance and recovers after you remove the fault and let it cool. Wear safety glasses, because a glass fuse can crack or throw hot pieces, put it in a proper closed holder or a clear box, keep your face back, never test above 5 V or on mains, and let blown fuses and polyfuses cool before touching.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
3 times ratingOpens within a second or two
2 times ratingOpens in several seconds
1.5 times ratingTakes much longer or holds
PolyfuseTrips then recovers when cooled

If it does not work

Nothing blows

Raise the current or wait longer.

Supply trips

Check it is in constant-current mode.

Readings vary

Start each fuse cold.

Holder gets hot

Stop and let everything cool.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the fuse and polyfuse lab?

Fuse 1 A glass (5 × 20 mm) × 3, Polyfuse (PTC resettable) 500 mA, Bench power supply 30 V 5 A and Resistor 10 kΩ.

How long does the fuse and polyfuse lab take to build?

About 60 minutes for a beginner maker, in 7 steps.

How do I know the fuse and polyfuse lab works?

3 times rating: Opens within a second or two. 2 times rating: Opens in several seconds. 1.5 times rating: Takes much longer or holds.

Nothing blows: what should I check?

Raise the current or wait longer.

Supply trips: what should I check?

Check it is in constant-current mode.

Readings vary: what should I check?

Start each fuse cold.

Holder gets hot: what should I check?

Stop and let everything cool.