Projects / Crop water stress from leaf temperature

Crop water stress from leaf temperature

Advanced2 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANOSHT3125.4°C

    Wire the three I2C devices

    Run an I2C scanner and check the three addresses.

  2. NANO25.5SHT31

    Check the thermometer

    Point it at your hand and a cup of warm water.

  3. NANO25.5SHT31

    Check the air sensor

    Shade it and compare with a known thermometer.

  4. NANO

    Aim at leaves

    Hold the sensor 30 cm from a healthy plant at midday.

  5. NANO

    Record the difference

    Write down the leaf minus air value.

  6. NANOSHT3125.5°C

    Compare two pots

    Water one and not the other for three days.

  7. NANO

    Watch the trend

    The unwatered plant should warm relative to the air.

In short

How do you build a crop water stress from leaf temperature?

An infrared thermometer measures canopy temperature and compares it with air temperature, because thirsty plants get warmer than air when they stop sweating. You need Arduino Nano, MLX90614 infrared thermometer, SHT31 temperature and humidity sensor and SSD1306 OLED Display. It takes 7 steps and about 120 minutes.

Level
Advanced
Time
About 120 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
MLX90614 VCCNano 5VPower, use the 5 V version of the module
MLX90614 GNDNano GNDGround
MLX90614 SDANano A4I2C data, address 0x5A
MLX90614 SCLNano A5I2C clock
SHT31 VCC and GNDNano 5V and GNDPower
SHT31 SDA and SCLNano A4 and A5I2C, address 0x44
OLED VCC and GNDNano 5V and GNDPower
OLED SDA and SCLNano A4 and A5I2C, address 0x3C

Code

Healthy leaves cool themselves by sweating, so the leaf is usually at or below air temperature in sun. When a plant is short of water it closes its pores, stops sweating and warms up, so a canopy that is warmer than the air at midday is a sign of water stress. Measure at midday in full sun, aim the sensor at a patch of leaves from about 30 cm so that it sees only leaves and no soil or sky (its view is a cone), and keep the air sensor in shade. The result also depends on humidity and wind, so compare the same plant over several days or compare a watered pot with an unwatered one rather than using one number as a rule. Treat this as a trend tool and not a precise stress index. Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Libraries: Adafruit MLX90614, Adafruit SHT31, Adafruit SSD1306 and GFX.
#include <Wire.h>
#include <Adafruit_MLX90614.h>
#include <Adafruit_SHT31.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>

Adafruit_MLX90614 ir;
Adafruit_SHT31 sht;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);

void setup() {
  Serial.begin(9600);
  ir.begin();
  sht.begin(0x44);
  oled.begin(SSD1306_SWITCHCAPVCC, 0x3C);
  oled.setTextColor(WHITE);
}

void loop() {
  float leaf = 0;
  for (byte i = 0; i < 10; i++) { leaf += ir.readObjectTempC(); delay(50); }
  leaf /= 10;                                    // average to reduce noise
  float air = sht.readTemperature();
  float rh = sht.readHumidity();
  float diff = leaf - air;                       // canopy minus air

  oled.clearDisplay();
  oled.setTextSize(1);
  oled.setCursor(0, 0);  oled.print("Leaf "); oled.print(leaf, 1); oled.print(" C");
  oled.setCursor(0, 12); oled.print("Air  "); oled.print(air, 1); oled.print(" C  RH "); oled.print(rh, 0);
  oled.setTextSize(2);
  oled.setCursor(0, 30); oled.print(diff > 0 ? "+" : ""); oled.print(diff, 1); oled.print(" C");
  oled.setTextSize(1);
  oled.setCursor(0, 54);
  oled.print(diff > 2 ? "Possible stress" : (diff > 0 ? "Watch it" : "Cool, ok"));
  oled.display();
  Serial.print(leaf); Serial.print(","); Serial.print(air); Serial.print(","); Serial.println(diff);
  delay(2000);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

0.00,0.00,0.00

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Hand at 30 cmAbout 30 to 34 degrees
Healthy watered plant at middayLeaf at or below air temperature
Unwatered plant after daysLeaf noticeably warmer than air
Sensor aimed at soilMisleading, so avoid it

If it does not work

Reading looks wrong

Check the sensor sees only leaves and is not in shade.

Values jump

Wind and passing clouds change it; average more readings.

Device not found

Check I2C addresses and the 5 V module version.

OLED blank

Check its address 0x3C.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the crop water stress from leaf temperature?

Arduino Nano, MLX90614 infrared thermometer, SHT31 temperature and humidity sensor and SSD1306 OLED Display.

How long does the crop water stress from leaf temperature take to build?

About 120 minutes for a advanced maker, in 7 steps.

How do I know the crop water stress from leaf temperature works?

Hand at 30 cm: About 30 to 34 degrees. Healthy watered plant at midday: Leaf at or below air temperature. Unwatered plant after days: Leaf noticeably warmer than air.

Reading looks wrong: what should I check?

Check the sensor sees only leaves and is not in shade.

Values jump: what should I check?

Wind and passing clouds change it; average more readings.

Device not found: what should I check?

Check I2C addresses and the 5 V module version.

OLED blank: what should I check?

Check its address 0x3C.