Projects / Seedling height tracker

Seedling height tracker

Beginner1 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANO

    Mount the sensor

    Fix it 40 cm above the soil, looking straight down at the middle of the pot.

  2. NANODS323117:19

    Wire it

    Sensor and RTC on A4 and A5, SD on D10 and SPI pins, button on D4.

  3. NANOVL53L0X44 cm

    Set the zero

    With bare soil in the pot, press the button. The soil distance is saved.

  4. NANO

    Test

    Hold a ruler or a book at 10 cm under the sensor and check the height in the file.

  5. NANO

    Run it

    Plant a seedling. Leave the rig on. It logs one value a day at noon.

  6. NANO

    Compare

    Make two rigs with different lights, and chart the two files in a spreadsheet.

In short

How do you build a seedling height tracker?

A VL53L0X sensor above a pot measures plant height every day and plots how fast it grows under different lights. You need Arduino Nano, VL53L0X time-of-flight distance sensor, DS3231 RTC module, MicroSD Card Module, Tactile push button 6 mm, Jumper wires male to male (40 pcs, 20 cm) and USB A to micro-USB cable (data). It takes 6 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
VL53L0X VIN and GNDNano 5V and GNDSensor supply (the module has a regulator)
VL53L0X SDA and SCLNano A4 and A5I2C, address 0x29
RTC SDA and SCLNano A4 and A5Shared bus
SD module CSNano D10Chip select
SD module MOSI, MISO, SCKNano D11, D12, D13SPI
SD module VCC and GNDNano 5V and GNDSupply
Zero buttonNano D4 and GNDPress with the sensor over bare soil

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install "Adafruit VL53L0X" and "RTClib". SD and EEPROM come with the IDE. The sensor measures to the nearest part of the plant, so aim it at the top of the main stem and check with a ruler now and then. The sensor reads up to about 1.2 m indoors, but readings get noisy at long range and in bright sun.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Wire.h>
#include <Adafruit_VL53L0X.h>
#include <RTClib.h>
#include <SD.h>
#include <EEPROM.h>

Adafruit_VL53L0X lox;
RTC_DS3231 rtc;
const byte CS = 10, ZERO_BTN = 4;
const byte LOG_HOUR = 12;                              // measure once a day at noon
int soilMm = 400;
int lastDay = -1;

int readMm() {
  VL53L0X_RangingMeasurementData_t m;
  long sum = 0; byte n = 0;
  for (byte i = 0; i < 10; i++) {
    lox.rangingTest(&m, false);
    if (m.RangeStatus != 4) { sum += m.RangeMilliMeter; n++; }
    delay(60);
  }
  return n ? sum / n : -1;
}

void setup() {
  pinMode(ZERO_BTN, INPUT_PULLUP);
  Serial.begin(9600);
  lox.begin();
  rtc.begin();
  if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__)));
  SD.begin(CS);
  int saved; EEPROM.get(0, saved);
  if (saved > 50 && saved < 1200) soilMm = saved;
}

void loop() {
  if (digitalRead(ZERO_BTN) == LOW) {                  // zero point: the distance to the bare soil
    int d = readMm();
    if (d > 0) { soilMm = d; EEPROM.put(0, soilMm); Serial.print("Soil at "); Serial.println(soilMm); }
    delay(500);
  }
  DateTime t = rtc.now();
  if (t.hour() == LOG_HOUR && t.day() != lastDay) {
    int d = readMm();
    if (d > 0) {
      lastDay = t.day();
      File f = SD.open("GROWTH.CSV", FILE_WRITE);
      if (f) {
        if (f.size() == 0) f.println("date,height_mm");
        f.print(t.year()); f.print('-'); f.print(t.month()); f.print('-'); f.print(t.day()); f.print(',');
        f.println(soilMm - d);                         // plant height is the soil distance minus the plant distance
        f.close();
      }
    }
  }
  delay(1000);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Zero button on bare soilSaves the distance
Object 10 cm above the soilLogs about 100 mm
A day laterAnother line in GROWTH.CSV
Power cycleZero distance restored

If it does not work

No readings

Sensor not found. Check the I2C wiring and address.

Heights jump around

The sensor sees leaves and the pot rim differently. Aim at the stem tip and average more.

No file

SD card not FAT32 or wrong CS pin.

Wrong date

The RTC lost its time. Re-upload to set it.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the seedling height tracker?

Arduino Nano, VL53L0X time-of-flight distance sensor, DS3231 RTC module, MicroSD Card Module, Tactile push button 6 mm, Jumper wires male to male (40 pcs, 20 cm) and USB A to micro-USB cable (data).

How long does the seedling height tracker take to build?

About 60 minutes for a beginner maker, in 6 steps.

How do I know the seedling height tracker works?

Zero button on bare soil: Saves the distance. Object 10 cm above the soil: Logs about 100 mm. A day later: Another line in GROWTH.CSV.

No readings: what should I check?

Sensor not found. Check the I2C wiring and address.

Heights jump around: what should I check?

The sensor sees leaves and the pot rim differently. Aim at the stem tip and average more.

No file: what should I check?

SD card not FAT32 or wrong CS pin.

Wrong date: what should I check?

The RTC lost its time. Re-upload to set it.