Projects / Pico W plant moisture web page

Pico W plant moisture web page

Beginner2 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. PICO

    Wire the sensor

    VCC to 3V3(OUT), GND to GND, AOUT to GP26.

  2. PICO

    Measure the dry reading

    Print read_raw() with the sensor held in dry air and note the number.

  3. PICO

    Measure the wet reading

    Dip the tip, up to the line only, in a glass of water and note the number.

  4. PICO

    Edit the program

    Put those two numbers in DRY and WET, and your Wi-Fi name and password in the placeholders.

  5. PICO

    Run the program

    The shell prints an address like http://192.168.1.50.

  6. PICO

    Open the address

    On a phone or computer on the same network.

  7. PICOCAPACITIsoil 34%

    Push the sensor into the soil

    Refresh to see the reading change.

In short

How do you build a pico W plant moisture web page?

A Pico W reads a capacitive soil moisture module and serves a dry, moist or wet message on a page on your home Wi-Fi. You need Raspberry Pi Pico W, Capacitive Soil Moisture Module and Breadboard 830 Tie Points. It takes 7 steps and about 120 minutes.

Level
Beginner
Time
About 120 min
Parts
3

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Moisture module VCCPico W 3V3(OUT) pin 36Power at 3.3 V
Moisture module GNDPico W GND pin 38Common ground
Moisture module AOUTPico W GP26 pin 31Analog signal to ADC0

Code

A capacitive soil sensor measures how much water is in the soil by sensing how the soil changes the electric field between two plates on the board, so nothing touches the soil with bare metal and the sensor does not corrode like the older two-prong type. It gives out a voltage that goes down as the soil gets wetter. The Pico W reads that voltage as a number between 0 and 65535, averages ten readings to smooth out noise, and turns it into a percentage using two numbers you measure yourself: the reading in dry air and the reading with the sensor tip in a glass of water. The Pico W joins your home Wi-Fi and runs a very small web server, so you can open the page on a phone on the same network. Push the sensor into the soil only up to the line on the board and keep the electronics at the top dry. Keep the page on your home network and do not forward a router port to it. The Wi-Fi name and password are placeholders; use your own and never share a copy with the real ones in it.

import time
import network
import socket
from machine import ADC

SSID = "YOUR_WIFI_NAME"                             # placeholders: use your own network
PASSWORD = "YOUR_WIFI_PASSWORD"

DRY = 50000                                         # reading in dry air, replace after you measure
WET = 22000                                         # reading in a glass of water, replace after you measure

sensor = ADC(26)

def read_raw():
    total = 0
    for _ in range(10):
        total += sensor.read_u16()
        time.sleep_ms(10)
    return total // 10

def percent(raw):
    pct = (DRY - raw) * 100 // (DRY - WET)
    return max(0, min(100, pct))

wlan = network.WLAN(network.STA_IF)
wlan.active(True)
wlan.connect(SSID, PASSWORD)
for _ in range(30):
    if wlan.isconnected():
        break
    time.sleep(0.5)
if not wlan.isconnected():
    raise RuntimeError("Wi-Fi did not connect, check the name and password")
print("Open http://" + wlan.ifconfig()[0])

server = socket.socket()
server.bind(("0.0.0.0", 80))
server.listen(1)

while True:
    client, addr = server.accept()
    client.recv(1024)
    raw = read_raw()
    pct = percent(raw)
    if pct < 30:
        message = "Dry: time to water"
    elif pct < 60:
        message = "Moist: fine for now"
    else:
        message = "Wet: leave it alone"
    page = ("<!DOCTYPE html><html><head><meta charset='utf-8'>"
            "<meta name='viewport' content='width=device-width, initial-scale=1'>"
            "<meta http-equiv='refresh' content='30'><title>Plant</title></head>"
            "<body style='font-family:sans-serif;text-align:center;margin-top:3em'>"
            "<h1>" + message + "</h1><p style='font-size:3em'>" + str(pct) + " %</p>"
            "<p>Raw reading " + str(raw) + "</p></body></html>")
    client.send("HTTP/1.0 200 OK\r\nContent-Type: text/html\r\n\r\n")
    client.send(page)
    client.close()

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Sensor in dry airNear 0 percent, Dry
Sensor in a glass of water up to the lineNear 100 percent, Wet
Sensor in damp soilBetween, Moist
Water the soilPercentage rises on the next refresh
Page refreshReloads by itself every 30 seconds

If it does not work

Page does not open

Check the address from the shell and that the phone is on the same Wi-Fi.

Wi-Fi does not connect

Check the name and password, and that the network is 2.4 GHz.

Percentage stuck at 0 or 100

Measure the dry and wet readings again and set DRY and WET.

Readings jump around

Keep the sensor still and away from your hands while measuring.

Reading falls for no reason

Water may have reached the electronics above the line, dry the module.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the pico W plant moisture web page?

Raspberry Pi Pico W, Capacitive Soil Moisture Module and Breadboard 830 Tie Points.

How long does the pico W plant moisture web page take to build?

About 120 minutes for a beginner maker, in 7 steps.

How do I know the pico W plant moisture web page works?

Sensor in dry air: Near 0 percent, Dry. Sensor in a glass of water up to the line: Near 100 percent, Wet. Sensor in damp soil: Between, Moist.

Page does not open: what should I check?

Check the address from the shell and that the phone is on the same Wi-Fi.

Wi-Fi does not connect: what should I check?

Check the name and password, and that the network is 2.4 GHz.

Percentage stuck at 0 or 100: what should I check?

Measure the dry and wet readings again and set DRY and WET.

Readings jump around: what should I check?

Keep the sensor still and away from your hands while measuring.