Projects / Raspberry Pi Pico first steps in MicroPython

Raspberry Pi Pico first steps in MicroPython

Beginner40 minGuided buildReviewed

Build it step by step

0 of 5 done
  1. PICOUSB

    Install MicroPython

    Hold BOOTSEL, plug in the Pico and install MicroPython from Thonny's interpreter settings.

  2. PICO10.7 mA

    Wire the LED

    GP15 through 330 Ω to the LED's long leg, short leg to GND.

  3. PICO

    Wire the button

    GP14 to one side, GND to the other.

  4. PICO

    Run

    Paste the code into Thonny and press Run. Then save it to the Pico as main.py.

  5. PICO10.7 mA

    Try the shell

    In the shell, type led.value(1) while it is stopped to switch the LED by hand.

In short

How do you build a raspberry Pi Pico first steps in MicroPython?

Flash MicroPython onto a Raspberry Pi Pico, blink an external LED with a timer, and toggle it with a button using an interrupt. You need Raspberry Pi Pico H, LED 5 mm red, Resistor 330 Ω, Tactile push button 6 mm, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and USB A to micro-USB cable (data). It takes 5 steps and about 40 minutes.

Level
Beginner
Time
About 40 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Pico GP15330 Ω, LED anode, LED cathode to GNDLED
Pico GP14Button, other side to GNDButton with internal pull-up
Pico GND (pin 38)Breadboard ground railGround

Code

MicroPython in Thonny. Hold BOOTSEL while plugging the Pico in, then in Thonny choose Tools > Options > Interpreter > MicroPython (Raspberry Pi Pico) > Install or update MicroPython. Save as main.py on the Pico to run at power-up.

from machine import Pin, Timer
import time

led = Pin(15, Pin.OUT)
button = Pin(14, Pin.IN, Pin.PULL_UP)
blinking = True
last_press = 0

def tick(t):
    if blinking:
        led.toggle()

def pressed(pin):
    global blinking, last_press
    now = time.ticks_ms()
    if time.ticks_diff(now, last_press) > 200:   # debounce
        blinking = not blinking
        led.value(0)
        print("Blinking" if blinking else "Stopped")
    last_press = now

Timer(freq=2, mode=Timer.PERIODIC, callback=tick)
button.irq(trigger=Pin.IRQ_FALLING, handler=pressed)

while True:
    time.sleep(1)       # the timer and interrupt do the work

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
After RunLED blinks: 2 timer ticks per second, so one full on-off per second
Button pressBlinking stops and the shell prints "Stopped"
Second pressBlinking resumes
Unplug and replug (saved as main.py)Starts blinking on its own

If it does not work

Thonny cannot find the Pico

Use a data cable, and select the Pico's port at the bottom right of Thonny.

LED never lights

Check its long leg goes to the resistor side, and that you used GP15 (physical pin 20).

One press counts twice

Raise the 200 ms debounce to 300.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the raspberry Pi Pico first steps in MicroPython?

Raspberry Pi Pico H, LED 5 mm red, Resistor 330 Ω, Tactile push button 6 mm, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and USB A to micro-USB cable (data). Raspberry Pi Pico H: The H version has headers soldered.

How long does the raspberry Pi Pico first steps in MicroPython take to build?

About 40 minutes for a beginner maker, in 5 steps.

How do I know the raspberry Pi Pico first steps in MicroPython works?

After Run: LED blinks: 2 timer ticks per second, so one full on-off per second. Button press: Blinking stops and the shell prints "Stopped". Second press: Blinking resumes.

Thonny cannot find the Pico: what should I check?

Use a data cable, and select the Pico's port at the bottom right of Thonny.

LED never lights: what should I check?

Check its long leg goes to the resistor side, and that you used GP15 (physical pin 20).

One press counts twice: what should I check?

Raise the 200 ms debounce to 300.