Projects / Wi-Fi pet feeder with portion control

Wi-Fi pet feeder with portion control

Intermediate4 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. ESP32

    Print the auger and hopper

    Test with dry food.

  2. ESP32

    Mount the stepper

    Shaft aligned with the auger.

  3. ESP32

    Test one turn

    Check the direction.

  4. ESP32

    Weigh a portion

    Set TURNS_PER_PORTION.

  5. ESP32

    Add the web page

    With your own password.

  6. ESP32

    Set the feeding times

    In the code.

  7. ESP32

    Watch it for a few days

    Before leaving it.

In short

How do you build a wi-Fi pet feeder with portion control?

A stepper turns an auger to drop measured portions of dry food at set times, and you can feed from your phone too. You need ESP32 DevKit V1, 28BYJ-48 Stepper Motor, ULN2003 driver board, 5 V 2 A USB adapter and 3D printer PLA filament 1.75 mm (1 kg). It takes 7 steps and about 240 minutes.

Level
Intermediate
Time
About 240 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
ULN2003 IN1, IN2, IN3, IN4ESP32 GPIO19, GPIO18, GPIO5, GPIO17Stepper coils
ULN2003 plus and minus5 V adapter, ground joined to the ESP32 GNDMotor power
Stepper plugULN2003 socket28BYJ-48 motor
ESP32Same 5 V adapter on VIN, or USBPower

Code

The 28BYJ-48 is a geared stepper, so it turns slowly with a lot of force, which is right for an auger that pushes dry food along a tube. The sketch counts turns, not time, so each portion is the same: weigh the food from one portion on a kitchen scale and change TURNS_PER_PORTION until it matches the amount your vet suggests. Two safeguards matter for a pet: a hard daily limit of portions, which the web page cannot get past, and the coils are switched off after each feed so the motor does not heat. The web page uses a password, so only you can feed from it; use it on your home network and do not open it to the internet. Print the auger and hopper in PLA, but be aware that printed layers can hold bacteria, so line the parts that touch the food with a food-safe liner or use food-safe containers, and wash them regularly. A jam can stall the motor, so look at the feeder a few times a day at first and do not rely on it as the only source of food or water for a pet that is left alone for days. Keep the cable and the motor out of the pet's reach. Arduino IDE with the ESP32 boards package 2.0.x, board "ESP32 Dev Module".

Runs on a virtual ESP32 Dev Module in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Pet feeder: feeds a set number of auger turns at two times a day and from a password-protected web page.
// Libraries: Stepper (built in), WebServer (built in with the ESP32 package). Board: ESP32. Fill in the placeholders.
#include <WiFi.h>
#include <WebServer.h>
#include <Stepper.h>
#include <time.h>
const char* WIFI_NAME = "YOUR_WIFI_NAME";
const char* WIFI_PASSWORD = "YOUR_WIFI_PASSWORD";
const char* PAGE_PASSWORD = "CHOOSE_A_PASSWORD";
const int FEED_HOURS[] = { 7, 18 };         // feeding times, 24 hour clock
const int TURNS_PER_PORTION = 3;            // calibrate: weigh the food from one portion
const int MAX_PORTIONS_PER_DAY = 4;         // a hard limit so a bug or a hacker cannot overfeed
Stepper motor(2048, 19, 5, 18, 17);         // 28BYJ-48: coil order IN1, IN3, IN2, IN4
WebServer server(80);
int portionsToday = 0, lastDay = -1, lastFedMinute = -1;
void releaseCoils() { for (int p : {19, 18, 5, 17}) digitalWrite(p, LOW); }
bool feed() {
  if (portionsToday >= MAX_PORTIONS_PER_DAY) return false;
  motor.step(2048 * TURNS_PER_PORTION);
  releaseCoils();
  portionsToday++;
  return true;
}
void handleRoot() {
  if (!server.authenticate("admin", PAGE_PASSWORD)) return server.requestAuthentication();
  String s = "<h1>Feeder</h1><p>Portions today: " + String(portionsToday) + " of " + String(MAX_PORTIONS_PER_DAY) + "</p>";
  s += "<form method='post' action='/feed'><button>Feed now</button></form>";
  server.send(200, "text/html", s);
}
void handleFeed() {
  if (!server.authenticate("admin", PAGE_PASSWORD)) return server.requestAuthentication();
  feed();
  server.sendHeader("Location", "/"); server.send(303);
}
void setup() {
  Serial.begin(115200);
  motor.setSpeed(8);                        // rpm, slow and strong
  WiFi.begin(WIFI_NAME, WIFI_PASSWORD);
  while (WiFi.status() != WL_CONNECTED) delay(500);
  configTime(19800, 0, "pool.ntp.org");     // India time, change for yours
  server.on("/", handleRoot);
  server.on("/feed", HTTP_POST, handleFeed);
  server.begin();
}
void loop() {
  server.handleClient();
  struct tm t;
  if (getLocalTime(&t)) {
    if (t.tm_mday != lastDay) { lastDay = t.tm_mday; portionsToday = 0; }          // new day, new allowance
    int minuteKey = t.tm_hour * 60 + t.tm_min;
    for (int h : FEED_HOURS) {
      if (t.tm_hour == h && t.tm_min == 0 && minuteKey != lastFedMinute) { lastFedMinute = minuteKey; feed(); }
    }
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Tap Feed nowAuger turns and food drops
Weigh one portionMatches the amount you set
At the set timeFeeds once
Fifth feed in a dayRefused

If it does not work

Motor buzzes

Check the coil order 19, 5, 18, 17.

Food jams

Use a larger auger gap and dry, even food.

Times are wrong

Check the time zone offset in configTime.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the wi-Fi pet feeder with portion control?

ESP32 DevKit V1, 28BYJ-48 Stepper Motor, ULN2003 driver board, 5 V 2 A USB adapter and 3D printer PLA filament 1.75 mm (1 kg).

How long does the wi-Fi pet feeder with portion control take to build?

About 240 minutes for a intermediate maker, in 7 steps.

How do I know the wi-Fi pet feeder with portion control works?

Tap Feed now: Auger turns and food drops. Weigh one portion: Matches the amount you set. At the set time: Feeds once.

Motor buzzes: what should I check?

Check the coil order 19, 5, 18, 17.

Food jams: what should I check?

Use a larger auger gap and dry, even food.

Times are wrong: what should I check?

Check the time zone offset in configTime.