Projects / Parts drawer finder

Parts drawer finder

Intermediate3 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. ESP32

    Number the drawers

    LED 1 for the first drawer, and so on.

  2. ESP3212.0 mA

    Fit the strip

    One LED behind each label.

  3. ESP32

    Light a drawer

    Test each LED in turn.

  4. ESP32

    Write the list

    Part name and LED number.

  5. ESP32

    Serve the search page

    Open it on your phone.

  6. ESP32

    Light the match

    Green LED on the drawer.

  7. ESP32

    Add stock counts

    Show how many are left.

In short

How do you build a parts drawer finder?

Search for a part on your phone and an LED lights the drawer it is in. You need ESP32 DevKit V1, WS2812B strip 5 m (30 LEDs/m), 5 V 2 A USB adapter, Resistor 330 Ω and Electrolytic capacitor 1000 µF. It takes 7 steps and about 180 minutes.

Level
Intermediate
Time
About 180 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
5 V adapter plus and minusLED strip 5V and GNDLED power
1000 µF capacitorAcross the strip 5V and GNDAbsorbs switching spikes
ESP32 GPIO5330 Ω resistor to strip DINData
ESP32 GNDStrip GNDCommon ground
ESP32 VIN5 V adapter plusPower the board

Code

Stick one LED of a strip behind each drawer label, and keep a list that maps each part to an LED number; searching matches any part whose name contains your text and lights those LEDs in green, so searching resistor lights every resistor drawer at once. Enter your own Wi-Fi name and password in the placeholders and never share the sketch with them filled in. Only a few LEDs light at once and at low brightness, so a 5 V 2 A adapter is plenty for the whole strip; keep the power capacitor and the 330 Ω data resistor in place. The page has no password, so keep it on your home network only. Later you can add stock counts and a page for adding parts, and store the list in a file instead of the sketch.

Runs on a virtual ESP32 Dev Module in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Parts drawer finder: type a part name, the drawer's LED lights. Library: FastLED. Board: ESP32 Dev Module.
#include <WiFi.h>
#include <WebServer.h>
#include <FastLED.h>
const char* SSID = "YOUR_WIFI_NAME";
const char* PASS = "YOUR_WIFI_PASSWORD";
#define NUM_LEDS 40
CRGB leds[NUM_LEDS];
WebServer server(80);
struct Part { const char* name; int led; };
Part parts[] = {
  {"resistor 10k", 0}, {"resistor 1k", 1}, {"capacitor 100nF", 2}, {"led red", 3},
  {"nano", 4}, {"esp32", 5}, {"relay module", 6}, {"servo sg90", 7}
};
const int N = sizeof(parts) / sizeof(parts[0]);
String page(String msg) {
  return "<html><body style='font-family:sans-serif'><h2>Find a part</h2>"
         "<form action='/find'><input name='q' autofocus> <input type='submit' value='Light it'></form>"
         "<p>" + msg + "</p></body></html>";
}
void handleFind() {
  String q = server.arg("q"); q.toLowerCase();
  FastLED.clear();
  String found = "";
  for (int i = 0; i < N; i++) {
    if (String(parts[i].name).indexOf(q) >= 0 && q.length() > 0) {
      leds[parts[i].led] = CRGB(0, 80, 0);
      found += String(parts[i].name) + " (drawer " + String(parts[i].led + 1) + ")<br>";
    }
  }
  FastLED.show();
  server.send(200, "text/html", page(found == "" ? "Nothing found" : found));
}
void setup() {
  FastLED.addLeds<WS2812B, 5, GRB>(leds, NUM_LEDS);
  FastLED.setBrightness(60);
  FastLED.clear(); FastLED.show();
  WiFi.begin(SSID, PASS);
  while (WiFi.status() != WL_CONNECTED) delay(300);
  server.on("/", []() { server.send(200, "text/html", page("")); });
  server.on("/find", handleFind);
  server.begin();
}
void loop() { server.handleClient(); }

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Search resistorAll resistor drawers light
Search esp32Only that drawer lights
Nothing foundAll LEDs off
PageOpens on a phone on your Wi-Fi

If it does not work

Page will not load

Check the Wi-Fi details and the IP address.

Wrong drawer lights

Check the strip direction and the numbering.

Flicker

Add the capacitor and the data resistor.

Colours wrong

Change GRB to RGB in the sketch.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the parts drawer finder?

ESP32 DevKit V1, WS2812B strip 5 m (30 LEDs/m), 5 V 2 A USB adapter, Resistor 330 Ω and Electrolytic capacitor 1000 µF.

How long does the parts drawer finder take to build?

About 180 minutes for a intermediate maker, in 7 steps.

How do I know the parts drawer finder works?

Search resistor: All resistor drawers light. Search esp32: Only that drawer lights. Nothing found: All LEDs off.

Page will not load: what should I check?

Check the Wi-Fi details and the IP address.

Wrong drawer lights: what should I check?

Check the strip direction and the numbering.

Flicker: what should I check?

Add the capacitor and the data resistor.

Colours wrong: what should I check?

Change GRB to RGB in the sketch.