Projects / Open-collector wired AND

Open-collector wired AND

Two Hall sensors with open-collector outputs share one wire and a pull-up resistor, so the wire goes low when either sensor sees a magnet. You see a wired AND made from nothing but a wire, and why buses such as I2C work this way.

Intermediate1.2 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Wire both sensors to 5V, GND and their own pins

    Outputs to D3 and D4.

  2. NANO

    Nothing extra is needed for step one

    The sketch turns on the Nano's own pull-ups.

  3. NANO

    Upload and bring the magnet to each sensor

    Each reads 0 on its own.

  4. NANO

    Join the two outputs with a jumper wire

    Keep one 10 kilohm resistor to 5V.

  5. NANO

    Bring the magnet to sensor 1, then 2, then both

    Both pins now read the same.

  6. NANO

    Fill in a truth table

    Idle, one, the other, both.

  7. NANO

    Remove the jumper

    They are separate again.

In short

How do you build an open-collector wired AND?

Two Hall sensors with open-collector outputs share one wire and a pull-up resistor, so the wire goes low when either sensor sees a magnet. You see a wired AND made from nothing but a wire, and why buses such as I2C work this way. You need Arduino Nano, Hall Effect Sensor A3144 × 2, Resistor 10 kΩ, LED 5 mm red, Resistor 220 Ω, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 70 minutes.

Level
Intermediate
Time
About 70 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Both A3144 pin 1 (VCC)Nano 5VPower
Both A3144 pin 2 (GND)Nano GNDCommon ground
Sensor 1 output (pin 3)Nano D3Read on its own at first
Sensor 2 output (pin 3)Nano D4Read on its own at first
Jumper wireJoins the two output wires togetherAdded in step two to make the shared wire
10 kilohm resistorJoined output wires to 5VThe pull-up for the shared wire
LED long legNano D8 through a 220 ohm resistor, short leg to GNDLights when D3 reads low

Code

The A3144 has an open-collector output. It can pull its output wire down to ground, but it cannot push it up, and it needs a resistor to 5 volts to bring the wire high again. That makes it safe to join two outputs together, because they can never fight each other. In step one the two output wires go to separate pins, each held high by the Nano's own pull-up. In step two you add a jumper wire that joins them, with one 10 kilohm resistor to 5 volts, and now both pins read the same shared wire. The shared wire is high only when both sensors are idle, and low when either one pulls it down, which is the logic of an AND on the idle-high signals. Bring a magnet to sensor 1, then to sensor 2, then to both, and see the table of readings. This is exactly how I2C lets many chips share one wire. Use small magnets, keep them away from phones and cards, and check the pin order of your sensor, since a wrong power connection can ruin it.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t OUT1_PIN = 3;
const uint8_t OUT2_PIN = 4;
const uint8_t LED_PIN = 8;

int last1 = -1, last2 = -1;

void setup() {
  pinMode(OUT1_PIN, INPUT_PULLUP);   // the Nano's own pull-ups serve step one
  pinMode(OUT2_PIN, INPUT_PULLUP);   // the 10 kilohm resistor makes the shared wire firmer
  pinMode(LED_PIN, OUTPUT);
  Serial.begin(9600);
  Serial.println("sensor1  sensor2   (1 = idle, 0 = magnet near)");
}

void loop() {
  int s1 = digitalRead(OUT1_PIN);
  int s2 = digitalRead(OUT2_PIN);
  digitalWrite(LED_PIN, s1 == LOW ? HIGH : LOW);
  if (s1 != last1 || s2 != last2) {
    last1 = s1; last2 = s2;
    Serial.print(s1);
    Serial.print("        ");
    Serial.println(s2);
  }
  delay(20);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

sensor1  sensor2   (1 = idle, 0 = magnet near)
1        1

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Separate outputsEach pin follows its own sensor
Joined outputs, no magnetBoth read 1
Joined, magnet at either sensorBoth read 0
Joined, magnet at bothBoth read 0
LEDLights whenever the shared wire is low

If it does not work

Both always read 0

Check the pull-up resistor goes to 5V and not GND.

Neither responds to the magnet

Turn the magnet round or try the other face.

Sensor gets warm

Disconnect, the power pins may be swapped.

Joined wire stays low

A magnet may be left near one of the sensors.

No serial text

Set 9600 baud.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the open-collector wired AND?

Arduino Nano, Hall Effect Sensor A3144 × 2, Resistor 10 kΩ, LED 5 mm red, Resistor 220 Ω, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the open-collector wired AND take to build?

About 70 minutes for a intermediate maker, in 7 steps.

How do I know the open-collector wired AND works?

Separate outputs: Each pin follows its own sensor. Joined outputs, no magnet: Both read 1. Joined, magnet at either sensor: Both read 0.

Both always read 0: what should I check?

Check the pull-up resistor goes to 5V and not GND.

Neither responds to the magnet: what should I check?

Turn the magnet round or try the other face.

Sensor gets warm: what should I check?

Disconnect, the power pins may be swapped.

Joined wire stays low: what should I check?

A magnet may be left near one of the sensors.