Projects / Active low-pass and high-pass filters

Active low-pass and high-pass filters

Intermediate2 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. TL072DUAL

    Check the supply

    Measure +V, 0 V and -V from the dual-rail module before connecting the chip.

  2. Build the low-pass

    Wire the Sallen-Key stage as in the table.

  3. Feed in a tone

    Use a phone tone generator app or a signal generator, with a 100 Hz sine at about 0.5 V peak.

  4. Measure the output

    Read it with an oscilloscope, a sound card scope program or an AC meter.

  5. Sweep the frequency

    Note the gain at 100, 300, 1 k, 2 k, 5 k and 10 kHz and plot gain against frequency.

  6. Find the cut-off

    It is where the output drops to about 0.7 of the input.

  7. Swap to high-pass

    Rewire with R and C swapped and repeat the sweep.

In short

How do you build an active low-pass and high-pass filters?

Sallen-Key filters with a TL072 pass frequencies below or above a set point, measured with a tone generator. You need TL072 dual JFET op-amp, Resistor 10 kΩ × 4, Ceramic capacitor 10 nF × 4, Ceramic Capacitor 100 nF × 2, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and Dual-rail ±12 V DC-DC module. It takes 7 steps and about 120 minutes.

Level
Intermediate
Time
About 120 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Dual-rail module + railTL072 pin 8 (V+)Positive supply
Dual-rail module - railTL072 pin 4 (V-)Negative supply
Dual-rail module 0 VBreadboard ground railSignal ground
100 nF capacitorsPin 8 to ground and pin 4 to groundSupply decoupling
Signal in10 kΩ resistor R1Input of the low-pass filter
R1 other endNode A, then 10 kΩ resistor R2Sallen-Key first stage
R2 other endNode B and TL072 pin 3 (IN+A)Non-inverting input
10 nF capacitors in parallel (20 nF)Node A and TL072 pin 1 (OUT)Feedback capacitor C1
10 nF capacitorNode B and groundShunt capacitor C2
TL072 pin 1 (OUT)TL072 pin 2 (IN-A)Unity-gain follower
TL072 pin 1Output to the meter or sound cardFiltered signal

No code needed

No code. Supply the TL072 from a small dual-rail module (for example +12 V and -12 V, or whatever it is labelled) and use its middle terminal as signal ground. The low-pass design uses R = 10 kΩ, C1 = 20 nF (two 10 nF in parallel) and C2 = 10 nF, which gives a Butterworth response with a cut-off near 1.1 kHz and a second-order slope of 12 dB per octave: fc = 1 ÷ (2π R √(C1·C2)). For the high-pass version swap each R and C in the positions: use C = 10 nF in the two series positions and R = 10 kΩ to ground and feedback, which gives about 1.6 kHz with a gentler knee. Keep input signals under 1 V peak.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
100 HzOutput about equal to input
1.1 kHzOutput about 0.7 of the input
10 kHzOutput much smaller (about 1 percent)
High-pass version at 100 HzSmall output, and large at 10 kHz

If it does not work

No output

Check the +V and -V supply on pins 8 and 4 and the pin 3 connection.

Output clips

Reduce the input amplitude.

Cut-off is wrong

Check the capacitor values and the parallel pair.

Noise

Add the 100 nF capacitors close to the chip and keep input leads short.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the active low-pass and high-pass filters?

TL072 dual JFET op-amp, Resistor 10 kΩ × 4, Ceramic capacitor 10 nF × 4, Ceramic Capacitor 100 nF × 2, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and Dual-rail ±12 V DC-DC module.

How long does the active low-pass and high-pass filters take to build?

About 120 minutes for a intermediate maker, in 7 steps.

How do I know the active low-pass and high-pass filters works?

100 Hz: Output about equal to input. 1.1 kHz: Output about 0.7 of the input. 10 kHz: Output much smaller (about 1 percent).

No output: what should I check?

Check the +V and -V supply on pins 8 and 4 and the pin 3 connection.

Output clips: what should I check?

Reduce the input amplitude.

Cut-off is wrong: what should I check?

Check the capacitor values and the parallel pair.

Noise: what should I check?

Add the 100 nF capacitors close to the chip and keep input leads short.